A plane wall, 5 mx 5 m x 15 cm wide, in steady state, is exposed to two airstreams, one on el-ther side of the wall. The left side of the wall is exposed to an airstream of Too,1 =velocity of u∞,1 = 1 m/s. the right side of the wall is exposed to an airstream of T∞,2 = 25 °C and a= 200 °C and avelocity of U2 = 6 m/s. (40points)Air (stream 1; Tf≈ 350K) v = 20.92 x 106 m²/s, k = 0.0300 W/m.K, Pr = 0.700Air (stream 2; T≈ 300K): v= 15.89 x 106 m²/s, k = 0.0263 W/m.K, Pr= 0.707Thermophysical properties of the wall: k = 1 W/m.K, p = 545 kg/m³, and c = 2720 J/kg.K(a) Determine the average coefficients of convection on both sides of the wall.(b) Determine the average heat flux through the wall. Clearly indicate direction.(c) Determine the temperatures on both the left and right sides of the wall (in °C).Too,11400.115 cmToo,2Uoo.2

Step 1: Step 2: Step 3: Step 4:

Answered: A plane wall, 5 mx 5 m x 15 cm wide, in…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

the tube length is 1m.
In mechanical fluid
Air enters a duct (100 cm *10̟cm*10 cm) at 32°C at a rate of 0.28m /min to cool 138 W electronic component placed on the duct. Assuming 85 percent of the heat generated inside is transferred to air flowing through the duct and the remaining 15 percent is lost through the outer surfaces of the duct. What is the exit temperature of air (°C)? C,= 1007 J/kg.°C, v =1.654×10-S m²/s, p 1.146 kg/m Pr = 0.7268, k = 0.02625 W/m.°C Select one or more:
A steam pipe with outside diameter 10 mm, passes through a room, the surface temperature of the pipe is 100 °C and the air is at 25 °C. Convection coefficient is 15 W/ m2.K. The heat transfer from a tube of length 5 m is: Select one: a. 1767 W b. 1767 W/ m c. 1767 W /m2 d. 176 W e. 1765 W
Air at 25 ° C blows over the hot steel plate whose surface temperature is maintained at 150 ° C. The plates are 50 cm x 40 cm in dimensions and 2.5 cm thick. The convection heat transfer coefficient on the upper surface is 20 W / (m² ° C). The thermal conductivity of steel is 45 W / (m ° C). Calculate the hourly heat loss from the plate surface. a. heat loss per hour = Answer kJ. b. If the reverse side surface temperature is maintained, determine the hourly heat loss occurring = Answer kJ.
Q5/A 400 m² light-colored swimming pool is located in a normal suburban site, where the measured wind speed at 10 m height is 2 m/s. The water temperature is 25 °C, the ambient air temperature is 10 °C, and relative humidity is 60%. There are no swimmers in the pool, the temperature of the make-up water is 20 °C, and the solar irradiation on a horizontal surface for the day is 15 MJ/m2-d. Neglect heat losses due to evaporation and radiation. How much energy must the solar system supply (Qss) to the pool to keep its temperature to 25 °C? Take: a = Solar absorptance (a = 0.85 for light-colored pools; a = 0.90 for dark colored pools).
solve both, show all steps, assumptions, comments, and solutions
!
4. For a flat plate, the transition from the free convection boundary layer to thefree convection turbulent boundary layer takes place at a Rayleigh number ofabout Ra = 1E9. A flat plate at 70 C is placed in a colder medium at 27 C. Findthe location on the plate where this transition takes if the plate is placed in:a) air, b) Ammonia, c) water. All fluids are at 1 atm.
A conductor with a diameter D= 0.8 cm, covered by an electric current, passes through an environment at T∞= 30 °C with convective heat transfer coefficient h= 120 W/(m² °C). The conductor temperature must be maintained at Ti= 130 °C. Calculate the rate of heat loss per meter of conductor length with:a) the uncoated conductor;b) the conductor covered with bakelite [k = 1.2 W/(m°C)] with a radius corresponding to the critical insulation radius.
A sab 15 cm Later, one of the other surface temp is at 20°C initially, 100°C. and the increased to 50°C. profile in the slob ofter 3 min, using finste differences method. calculate the temp s += 15 min Dx = 5 cm 1.10 of m²/s The equation describing the system: d. 227 before 1 2 3 after 20°C 20°C 20°C 20°C 20°C 20°C 50°C +=0 100°C 20°C ? 50°C +=1₁5 105C ? 50°C + = 3 100°L ? of 2 thickness is surfaces is 2 maint oined increased to 0 Be 2x
A person weighing 25 kg jumps on a jumper, the time interval is 10 seconds between hitting the child with the jump and returning it again, the highest height reaches 10 cm mv. reaction force is required p 7:29

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS