5. A hollow steel rod is pinned on both ends, and loaded as shown in the figure. Find the safety factor. The steel properties are: a. modulus = 207 GPa b. yield strength = 294.8 MPa ultimate strength = 395 MPa C. y P = 5 kN Ꮓ x O O A OD = 20 mm ID = 15 mm Ꮓ L = 750 mm x

5. A hollow steel rod is pinned on both ends, and loaded as shown in the figure. Find the safety factor. The steel properties are: a. modulus = 207 GPa b. yield strength = 294.8 MPa ultimate strength = 395 MPa C. y P = 5 kN Ꮓ x O O A OD = 20 mm ID = 15 mm Ꮓ L = 750 mm x

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.10.3P: A flat bar of width b and thickness t has a hole of diameter d drilled through it (see figure). The...

See similar textbooks

Related questions

Q: FOR THE SQUARE WAVE SIGNAL, SPELL THE SIGNAL OBTAINED WITH 12 TERMS FROM THE FOURIER SERIES.

A: To find the Fourier series expansion of the square wave signal depicted in the image and then to…

Q: Handwrite please

A: • Fouling factor on the gas side Rf,i=0.0015 m2⋅K/W

Q: Select three games of your choice and analyze the subverting conventions that are applied in these…

A: In conclusion, the graphic designs of The Stanley Parable, Undertale, and Journey all challenge…

Q: The rotating shaft in the given figure is machined from AISI 1020 CD steel. It is subjected to a…

Q: Please give detailed solution asap. Don't use chatgpt,It will be useless.

A: Approach to solving the question: Detailed explanation: Examples: Key references:

Q: Please calculate the centroid x and y bar, and Ixx for the following shapes. Show all work with neat…

A: Given lengths, width, and individual centroids of the rectangles from the figure above we can solve…

Q: A mass of 20 kg is suspended from a spring of stiffness 10,000 N/m. The vertical motion of the mass…

Q: (25 pts) The 50-lb block rests on the smooth surface. A force F = (40+s²) lb, which s is in ft, acts…

Q: The cold-formed section of aluminum shown in figure is subjected to a torque of T = 4,312 Nmm.…

A: To calculate the maximum shear stress in the cold-formed aluminum section, we'll use the torsion…

Q: Please calculate the centroid x and y bar, and Ixx for the following shapes. Show all work with neat…

A: I have opened the image. Let me calculate the centroid (x̄, ȳ) and the moment of inertia (Ixx) for…

Q: For the beam loaded as shown in Figure 3, the vertical reaction at support B is 6.53 kN.a)…

A: First, we need to calculate the reaction at point A. The total load on the beam is the sum of the…

Q: Dashboard Course Modules: (MA... P Pearson MyLab and... User Settings Purchase Options…

Q: The water pressure acting on a masonry dam varies as shown. If the dam is 20 ft wide, determine the…

A: Rtrap= 21×height×(top pressure+bottom pressure) Rtrap=12×(12−7.5)×(750+1217)=12×4.5×1967=4425.75…

Q: Solve fast please

Q: The inclined-tube manometer shown in Fig. 2-23 is used to measure small pressure changes. Determine…

A: In a U-tube or an inclined tube manometer, the simple physics is to balance the pressures on the…

Q: Find the magnitudes & natures of all the forces in the members of the pin-jointed truss (Note:…

A: Step 1: Step 2: Step 3: Step 4:

Q: A beam 15 m long is simply supported at the left end and at 3 m from the right end. It carries…

A: Step 1: Step 2: Step 3: Step 4:

Q: please with solving

Q: Please solve in a handwritten format. No gpt

A: The answer has been attached in the form of an image:

Q: The mean dimensions of the cross section of the leading edge and torsion box of an airplane wing can…

Q: Solve the problem correctly in a handwritten format. Strictly chatgpt not allowed

A: Step 1: Step 2:

Q: Determine the magnitude of M if the resultant of the forces and couple M passes through point O.

A: See image below for the solution.

Q: The concrete pier is subjected to soil pressure that causes the line loads shown. Show full solution…

A: Step 1: Step 2: Step 3: Step 4:

Q: i dont understand this concept on how to fill out this table?

A: For each quantity, use the given SI units to find the dimension of the quantity. The dimension…

Q: 7. (15 points). A simply supported beam (W 8x58) is subject to the loading shown below. Plot the…

A: Step 1:Step 2:Step 3:Step 4:

Q: FOR THE SQUARE WAVE SIGNAL, SPELL THE SIGNAL OBTAINED WITH 12 TERMS FROM THE FOURIER SERIES. No use…

Q: For a building that is to be used for mix use offices and high technology labs where the owner want…

A: Commissioning (Cx) is a quality assurance process that ensures that a building's systems are…

Q: A pressure gauge at the top of an oil well 18,000 ft deep registers 2,000 psig. Thebottom 4,000-ft…

A: 10.7316ft3\cdotppsi/(lbm\cdotpmol\cdotpR) The pressure at the oil/gas interface…

Q: vibrations- solve show all steps

Q: Using the nomogram and the information for the plate cam above (plate cam rotates at 300 rev/min)…

A: The problem is asking us to find the minimum radius of the prime circle for a plate cam that is…

Q: Please give me the solution in a handwritten solution. Don't use chatgpt,You must have to draw the…

A: Step 1:Step 2:Step 3:

Q: The truss is supported by a pin at A and a roller at B. (Figure 1) Figure y 10 kN 2 m- 4 m- X 2 m 5…

Q: Dry saturated steam at p1 = 3.5 MPa is contained in a cylinder-piston arrangement. It is brought…

Q: What do you mean by quasi-static process?

A: Approach to solving the question:ThermodynamicsDetailed explanation:A quasi-static process (also…

Q: A pressure gauge at the top of an oil well 18,000 ft deep registers 2,000 psig. Thebottom 4,000-ft…

A: Step 1:Step 2: Step 3: Step 4:

Q: Implement a predictive maintenance strategy within Liquified Natural Gas production line (data…

Q: Please do not give a typedout answer. They are hard to follow/read. Please write it out, draw a FBD…

Q: At what angle must the 320-lb force be applied in order that the resultant R of the two forces have…

A: Given, R = 1060 lb Let, F1 = 910 lbF2 = 320 lb The magnitude of the resultant force R can be…

Q: A. Suppose that a = 0.3 m and b = 1 m. 1. Find an expression for the steering angle of the inner…

Q: S 30mm 120° 150 90° Question 6 According to the S-8 curve provided blow, designing a disc cam…

A: Step 1: Step 2: Step 3: Step 4:

Q: Please solve it in a handwritten format with a free body diagram. Don't use chat gpt. (Diagram is…

A: Approach to solving the question: Detailed explanation:Examples: Key references:

Q: I need answer as fast as possible please

Q: determine whether the given differential equation is exact. If it is exact, solve it. (please solve…

Q: Water flows without friction through a horizontal pipe and enters a section where thecross-sectional…

A: According to the principle of continuity, A1V1=A2V2Where A1 and A2 are the cross-sectional…

Q: vibrations, show all steps and solution

Q: Resolve the following into x and y components given that ϴ = 70 deg:a) P1b) P2c) P3

A: Step 1: Step 2: Step 3: Step 4:

Q: (c) An aluminium bar having a cross-sectional area of 0.5 in² carries the axial loads applied at the…

A: Step 1: Step 2: Step 3: Step 4:

Q: Ayúdame a resolver este problema de flexión y resistencia de materiales.

Q: A rigid container contains m = 3 kg of air. The air changes from an initial state of P1 = 0.5 MPa…

Q: The nonhomogeneous plate weighing 60 kN has its center of gravity at G. Itis supported in the…

Question

Please answer all parts

5. A hollow steel rod is pinned on both ends, and
loaded as shown in the figure. Find the safety
factor.
The steel properties are:
a.
modulus = 207 GPa
b. yield strength = 294.8 MPa
ultimate strength = 395 MPa
C.
y
P = 5 kN
Ꮓ
x
O O
A
OD = 20 mm
ID = 15 mm
Ꮓ
L = 750 mm
x

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

A bar of monel metal with a length L = 9 in. and a diameter d = 0225 in. is loaded axially by a tensile force P (see figure). If the bar elongates by 0.0)95 in., what is the decrease in diameter
Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN. as shown in the figure. The cable has an effective modulus of elasticity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, that is the factor of safety with respect to failure of the cable?
A tension member constructed of an L inch angle section (see Table F-4(a) in Appendix F) is subjected to a tensile load P = 12.5 kips that acts through the point where the mid-lines of the legs intersect (see figure part a). Determine the maximum tensile stresser, in the angle section. Recompute the maximum tensile stress if two angles are used and P is applied as shown in the figure part b.
A column, pinned at top and bottom, is made up of two C 6 x 13 steel shapes (see figure) that act together. Find the buckling load (kips) if the gap is zero. Find required separation distance d(inches) so that the buckling load is the same in y and z directions. Assume that E = 30,000 ksi and L = 18 ft. Note that distance d is measured between the centroids of the two C shapes.
An idealized column is composed of rigid bars ABC and CD joined by an elastic connection with rotational stiffness ßRIat C. There is a roller support at B and an elastic support at D with translationa1 spring stiffness ß and rotational stiffness ßR2. Find the critical buckling loads for each of the two buckling modes of the column. Assume that L = 3 m, ß = 9 kN/m, and ßR]= ßR1= ßL2. Sketch the buckled mode shapes.
A vertical bar is loaded with axial loads at points B, C, and D. as shown in the figure. The bar is made of steel with a modulus of elasticity E = 29,000 ksi., The bar has a cross-sectional area of 8.24 in2. Calculate the displacements at points B, C, and D. Ignore the weight of the bar
A pressurized circular cylinder has a sealed cover plate fastened with steel bolts (see figure). The pressure P of the gas in the cylinder is290psi, the inside diameter D of the cylinder is 10.0 in., and the diameter dBof the bolts is 0.50 in. I f the allowable tensile stress in the bolts is 10,000 psi, find the number n of bolts needed to fasten the cover.
A high-strength steel bar used in a large crane has a diameter d = 2.00 in. (sec figure). The steel has a modulus of elasticity E = 29 × 10 psi and Poisson’s ratio is v = 0.29. Because of clearance requirements, the diameter of the bar is limited to 2.001 in. when it is compressed by axial forces. What is the largest compressive load Pmaxthat is permitted?
A steel column ( E = 30 X 103 ksi) that is fixed at the base and free at the top is constructed of a W8 x 35 wide-flange member (sec figure). The column is 9.0 ft long. The force P acting at the top of the column has an eccentricity e = 1.25 in. If P = 40 kips, what is the maximum compressive stress in the column? If the yield stress is 36 ksi and the required factor of safety with respect to yielding is 2.1, what is the allowable load Pallow?