Inth big below:-A500mBZoomс180011I=50AI-60A I-80406·0.70.8lag.unit)Teading PfP.FPlAI sing phase distributor of 3/cm =The distance from point A To B is 500mdistance from point A To C is /200mThe distance from point A To D is 3000mThe impedance of each part is.ZAB-0.51j0.8 -2/kmZBC= 0.7+71.2 12/1cmZCD = 1.3772.5 -2/1cmThe voltage of end for is VD= 220 VoltFind : 1- sending Voltagesenting power2- 5

Answered: Inth big below:- A 500m B Zoom с 180011…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

From step1, how did you get that 50+(80*j60/80+j60) = 78.8+j38.4? also in step 2, how did you get that 5/(0.0125-0.0167) = 143.63 + j191.89?
how to measure ripple factor and peak input and peak output voltage for this circuits ?
What is the ripple voltage in the recufier circuit given below. (Assume that V13V, f-50 Hz, R-120 C 40 mV)? 22V O05V OCT5V 18 Vsino C
The step down DC chopper uses DC source voltage V(dc) = 200 V and resistive load impedance of 10 ohm. The duty cycle is 0.4 the voltage drop across the switch may be taken as zero, Calculate : (a) Average and RMS value of output voltage. (b) Average and RMS value of output current.
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
%VAI ۲,۷ K/s 9:- Zain 4.5G+ A step down de chopper is connected to an R-52 and L. 10 mH. The de supply voltage is 100 V. The chopper is switching at a frequency of 1 kHz with a duty cycle of 50%. Determine the load current, Jo and the peak to peak ripple current as an absolute value and as percentage of de value. ☐ О Δ
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
1. Impedance is the total opposition to an AC circuit caused by electric penalty tions, the tra capa multiple pacitive systema 62 Fundamentals of AC Electricity Questions for This C a. 1. Draw a diagram of an AC sine wave and identify its peak voltage and peak-to-peak voltage levels. b. 2. Explain the term frequency as it refers to AC electricity. c. 3. Discuss the difference between a load center and a fused disconnect. 2. WE wa 4. Explain how you would test for voltage in a fusible dis- connect on the line-side and load-side terminals. vi ci 5. Trace the path of a generated AC voltage from the generat- ing station where it is produced to the point where you would connect it to a machine in a factory. Be sure to iden- tify all the important parts of the system between the gen- eration station and the disconnect on the machine. a. be 3. True or False inductive reactance, capacitive reactance, and resistan 2. The units of impedance are
Voltage at Va.
Why the tranformer rattigs are mentioned in KVA. Discuss in brief.
C. Draw a general sine wave V vs t and I vs t plot for a purely resistive and a purely inductive circuit and show leading lagging parameters and clearly mark the phase difference.
The three-phase half-wave converter shown in Figure is operated from a three-phase Y-connected 220-V. 60-Hz supply and a freewheeling diode is connected across the load. The load current with an average value of I, is continuous and the ripple content is negligible. If the delay angle alpha = alpha / 3, calculate (A) the displacement factor. and (B) the input power factor. टे Lond

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning