Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries.VpsRwwWrite the FORMULA for the total impedance of the circuit Ztot =Determine the numerical value of Ztot = 2890.5Determine the numerical value of $z= = 41Determine the current through the circuit:• I(PEAK) = 4.81E-3• I(RMS) = 3.404E-3Determine the voltage across the resistor:• VR(PEAK) = 7.387• VR(RMS) = 5.22✔✔ Amps✔AmpsWrite the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701Rx VoltsX VoltsDetermine the voltage across the inductor:• VL(PEAK) = 9.184• VL(RMS) = 6.49✔ VoltsVoltsLR²+ WL-✔ degrees2If a second circuit were connected in parallel with the inductor, this circuit would be considered as:O a low-pass filterO a capacitive switcherO a high-pass filterO an inductive rectifierO a radio tunerO a phase conjugate deflectorNOTE: In your formulas, use variables R, w, and L. Do not use f.X

Answered: Image /qna-images/answer/96a4e95a-2d41-4a75-93fc-3a8b9c4fcc46.jpg

shown in the Vps low is Write the FORMULA for the total impedance of the circuit Zut= R²+ cL- Write the FORMULA for the phase of the total impedance of the circuit -tan-12 R Determine the numerical value of Z-2090.5 Determine the numerical value of 41 Determine the current through the circuit: PEAK)-4818-3 (RMS)-3.404E-3 • Vn(RMS)-5.22 R ww Determine the voltage across the resistor: VPEAK-7.387 ✔Amps ✔Amps O a high-pass filter O an inductive rectifier x Voits x Voits Determine the voltage across the inductor: V(PEAK)-0184 V(RMS)-[6.40 ✔ Voits ✔Voits irce. The AC power source has an O a radio tuner O a phase conjugate deflector If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher ✓degrees x HZ. The resistor has a

shown in the Vps low is Write the FORMULA for the total impedance of the circuit Zut= R²+ cL- Write the FORMULA for the phase of the total impedance of the circuit -tan-12 R Determine the numerical value of Z-2090.5 Determine the numerical value of 41 Determine the current through the circuit: PEAK)-4818-3 (RMS)-3.404E-3 • Vn(RMS)-5.22 R ww Determine the voltage across the resistor: VPEAK-7.387 ✔Amps ✔Amps O a high-pass filter O an inductive rectifier x Voits x Voits Determine the voltage across the inductor: V(PEAK)-0184 V(RMS)-[6.40 ✔ Voits ✔Voits irce. The AC power source has an O a radio tuner O a phase conjugate deflector If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher ✓degrees x HZ. The resistor has a

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Problem 54: Express the following phasor currents and voltages as sine waves for f = 60 Hz. Notice that all these phasors are given in rms. a. I= 40 A Z20° b. V = 120 V Z10° c. I= 8 x 10-³AZ – 110° d. V = 6000 VZ– 180°
Find the RMS value..
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three- phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT RO- SO- To- : IR Is IT UL-380 V CARGA 1 P₁ = 950 W cos p1=0,5 ind. CARGA 2 P₂=1.140 W cos p₂=1 CARGA 3 P3=760 W cos p3=0,5 cap.
please explain each part on paper thank you i will like
Consider the circuit shown in Figure 1. V1 is a 7.2 kHz sine wave with an amplitude of 4 V.Figure 1: RC Circuit Schematic1. Determine the total impedance (Z) of the circuit.2. Using V1 as a zero-phase reference, calculate the values of the following:a) Amplitude and phase of current (I)b) Amplitude and phase of voltage across R1 (VR1)c) Amplitude and phase of voltage across C1 (VC1
A load has a leading power factor. a) Is it a capacitive or inductive load? b) Is the reactive power positive or negative? c) Repeat for a load with lagging power factor
Sine wave A has a positive-going zero crossing at 40°. Sine wave B has a positive-going zero crossing at 45°. Determine the phase angle between the two signals. What signal leads ? A Y-connected system can have wires. The (resultant) voltage between the hot legs (135V) is The phase angle between the phase voltage and the line voltage of a A-connected generator is degrees. The phase current produced by a certain 20V, Y-connected generator is 12A. The corresponding line current is A certain A-connected generator produces phase voltages of 30V. The magnitude of the line voltages are When the turns ratio of a transformer is 20 and the primary ac voltage is 6V, the secondary voltage is If 20W of power are applied to the primary of an ideal transformer with a turns ratio of 8, the power delivered to the secondary load is The turns required to match a 500 source to a 1000 load is
Find the sinusoidal and the rms phaser expression Vs = 120 sin (377t+0 degrees)