In a construction factory, three production lines were used to produce bricks, the produced bricks matched the specifications as shown in the following table, calculate the following: 1- The probability of obtaining a sample that not matched the specifications when taken randomly from the production of the factory 2-If a sample is taken and it not matched the specifications, what is the probability that it was produced from the first line? 3- If a sample is taken and it matched the specifications, what is the probability that it was produced from the second line? Production Line Third First 70 Second 80 Matching the specifications % 90

In a construction factory, three production lines were used to produce bricks, the produced bricks matched the specifications as shown in the following table, calculate the following: 1- The probability of obtaining a sample that not matched the specifications when taken randomly from the production of the factory 2-If a sample is taken and it not matched the specifications, what is the probability that it was produced from the first line? 3- If a sample is taken and it matched the specifications, what is the probability that it was produced from the second line? Production Line Third First 70 Second 80 Matching the specifications % 90

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 160-lb woman stands on a vinyl floor wearing stiletto high- heel shoes. The heel has the dimensions shown in (figure 1) Assume the entire weight is supported only by the heel of one shoe. Figure 12 in 6.5 in 63 in 1of1 Part A Determine the average normal stress she exerts on the floor. Express your answer in pounds per square inch to three significant figures. VAZ vec Submit Part B Request Answer Submit Determine the average normal stress developed when a man having the same weight is wearing flat-heeled shoes Express your answer in pounds per square inch to three significant figures. VAZO I ved Request Answer I ? 7
The granulation step is a very important step in the preparation procedure of ceramics. During the preparation of granules in a production facility, it has been observed that the granules in Figure 2 are obtained as a result of the process, while the granules are requested to be prepared as in Figure 1. a) What do you think are the reasons for the formation of granules in this way? (Write and explain 3 reasons). b) What precautions would you take to prevent this error from occurring in the next step? (Write and explain 2 precautions).
Answer the following: 1. Aggregates property that relates to the particle's ability to take in a liquid. 2. An investigation or trial to ascertain the true characteristics of a material/s. 3. Aggregates with diameter of 3 inches to 6 inches. 4. A mass formed by union of distinct but similar materials. Refers to granular mineral particles. 5. Used to examine materials and components in ways that do not harm the future usefulness and service of the material. 6. _________is the ratio between the Net weight of the aggregates to the volume.
What are the units of particle sizes, area, and volume and give examples of it’s typical calculation. Describe how particles can be characterized and why this method is important.
For material testing,Take one destructive and one non-destructive test and explain how both test procedures produce useful results.
The following mineral analysis was reported for a water sample taken from a municipal groundwater water well. Determine the total, carbonate and non carbonate hardness in mg/L as CaCO3 using the predominant polyvalent cation definition of hardness. All reported as "mg/L as the ion" Iron 0.2 Manganese 0.6 Ammonium 0.5 Sodium 4.7 Potassium 0.9 Calcium 67.2 Magnesium 39 Barium 0.5 Silica 20 Flouride 0.35 Boron 0.1 Nitrate 0 Chloride 4.5 Sulfate 29 Alkalinity 284 as CaCo3 pH 7.6 units
Q#01: "Small grains are used for grinding hard work materials and large grains are used for grinding soft work materials". Explain the reason(s) behind this statement.
Two suppliers manufacture a plastic gear used in a laser printer. The impact strength of these gears measures in foot-pounds is an important characteristic. A random sample of 10 gears from supplier 1 results in x₁ = 290 and s₁ = 12 while another random sample of 16 gears from the second supplier results in x2 = 321 and s₂ = 22. Is there evidence to support the claim that supplier 2 provides gears with higher mean impact strength. Use a =0.04, and assume that both populations are normally distributed with equal variances.
Please solve
A tensile load of 190 kN is applied to a round metal bar with a diameter of 16 mm and a gage length of 50 mm. Under this load the bar elastically deforms so that the gage length increases to 50.1349 mm and the diameter decreases to 15.99 mm. Determine the modulus of elasticity and Poisson