Given the following data below, Compute for the stress , strain and modulus of stiffness of each sample. Draw the graph of modulus of elasticity and modulus of stiffness for each item. Show your solutions. Given , L = 400mm W= 200 mm H= 700 mm. SAMPLE APPLIED DEFLECTION STRAIN STRESS MODULUS OF NO. LOAD (N) (mm) STIFFNES 1 3500 25 3800 35 4200 50 4 4650 75 5 4950 88 6. 5200 95 7 5580 120 5785 145 5980 160 10 6540 175

Given the following data below, Compute for the stress , strain and modulus of stiffness of each sample. Draw the graph of modulus of elasticity and modulus of stiffness for each item. Show your solutions. Given , L = 400mm W= 200 mm H= 700 mm. SAMPLE APPLIED DEFLECTION STRAIN STRESS MODULUS OF NO. LOAD (N) (mm) STIFFNES 1 3500 25 3800 35 4200 50 4 4650 75 5 4950 88 6. 5200 95 7 5580 120 5785 145 5980 160 10 6540 175

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Osec σij = The hydrostatic stress for the state of stress represented by oij given below is MPa [100 50 50 125 75 75 75 = 50 50 1 MPa
Given the torque-angle deformation curve below, estimate the shear modulus in GPa?. Where the length of the specimen is 273mm and the diameter is 19.3mm (Round your answer to nearest integer, e.g. 100, do not add units, use exact value of pi not 3.14) SC.O 45.0 35.0 25.0 20.0 5.0 0.20 040 050 0.60 0.70 0.80 0.90 Angle (") A S en eta ine f Your Answer: Answer Torque (N-m)
Som.
For the built-up shape shown in the figure, determine: a. The elastic section modulus considering bending about the horizontal axis. (ANS 518 x 103mm3). b. The elastic section modulus considering bending about the vertical axis (ANS 133 x 103mm3). c. The plastic section modulus about the horizontal axis in x103 mm3 (ANS 572) d. The plastic section modulus about the vertical axis in x103 mm3.(ANS 0.20)
Show detailed solution refer to the table of equations.
MECHANICS OF DEFORMABLE BODIES WRITE THE COMPLETE SOLUTIONS. UPVOTE WILL BE GIVEN. ANSWER IN 2 DECIMAL PLACES.
Could I please get a full written solution on how to answer question 6 for this past paper question please?
Consider the state of stress shown in 01, 02 = 20 MPa 40 MPa Opi 100 MPa Part A Determine the principal stresses. Enter your answers in megapascals to three significant figures separated by a comma. ANSWER: Q Tap image to zoom MPa Part B Specify the orientation of the principal plane. Express your answer in degrees to three significant figures. ANSWER:
Several buildings have foundations made of material such as concrete. In fact, the compressive strength of concrete is a critical factor in providing a firm foundation of structures. The stress-strain diagram of concrete shown below has the points of failure as indicated by dots. (a)Determine the Young's modulus for this particular concrete under compression. See stress-strain diagram in figure 05. * Tensile stress, 10' Pa 4.0 8.0 40 40 5.0 10.0 Compressive Tensile strain, 10 strain, 10 15.0 Compressive stress, 10' Pa Figure 05 25 GPa 25 MPa 25 KPa 0.04 nPa
Procedure: 1. Compression tests on specimens shall be made as soon as practicable after removal from the moist storage. A 28-day test shall be performed within +-20 hours of the 28thday. Test specimens shall be kept moist by any convenient method during the period between removals from moist storage and testing. They shall be tested in moist condition. 2. All test specimens for a given test age shall be broken within the permissible time tolerance prescribed below. TEST AGE PERMISSIBLE TOLERANCE 24 HOURS +-0.5 HOURS OR 2.1% 3 DAYS 2 HOURS OR 2.8% 7 DAYS 6 HOURS OR 3.6% 28 DAYS 20 HOURS OR 3.0% 90 DAYS 2 DAYS OR 2.2 % 3. With a clean rag or rush clean the bearing faces of the bearing blocks, test the specimens and exclusion controller (elastomeric cps). 4. Rest the specimen on the lower extrusion controller, place the top extrusion controller on the specimen, and check the spacing between the sides of the specimen and the extrusion controllers to ensure no contact between the cylinder…