Q5: A/A tensile test was conducted for a sample and the relationship between stress and strain was as shown in the following figure: Stress Strain stuess the point (44*7)) and emotion) 1 6.67 Mpa 0.00067 2 13.3 Mpa 0.00133 3 20 Mpa 0.002 4 24 Mpa 0.003 stram 5 22 Mpa 0.0035 Answer the following: 1- Calculate the modulus of elasticity. 2- Calculate the modulus of resilience. 3- The modulus of toughness is:

Q5: A/A tensile test was conducted for a sample and the relationship between stress and strain was as shown in the following figure: Stress Strain stuess the point (44*7)) and emotion) 1 6.67 Mpa 0.00067 2 13.3 Mpa 0.00133 3 20 Mpa 0.002 4 24 Mpa 0.003 stram 5 22 Mpa 0.0035 Answer the following: 1- Calculate the modulus of elasticity. 2- Calculate the modulus of resilience. 3- The modulus of toughness is:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the tensile strength in the Brazilian examination of the samples below shown in the table in which the best thickness was used
I need a step by step answer please :)
Question One Figure Q1 shows a stress state element in a material component. Analyse the element and calculate the principal stresses and positions of the principal planes in the component, using: 1.1 Formulae; 1.2 First principles 120 MPa 80 MPa need neat and clean handwritten solution of both parts for upvote Figure Q1. 25 MPa
A1 Find the stress in each cord of the system shown in fig. below if the cross section area of each cord is ?450 mm2 ELL 111111 45 2 750 B W =90 KN
Q5) A specimen of alloy having a rectangular cross section of dimensions 5 mm x 16 mm is deformed in tension. Using the Load (N) Length (mm) tabulated data to plot the engineering stress – strain curve and 75.000 4669.56 75.03 then calculate the following: 8985.96 75.08 12694.14 75.09 (a) Modulus of elasticity. 16264.98 75.14 17991.54 75.18 (b) The yield strength. 19816.2 75.26 22484.52 75.421 (c) The modulus of resilience. 24623.1 75.621 26369.28 75.846 28292.04 77.68
The stress-strain diagram for a bar of steel alloy is shown. Determine: a) The modulus of Elasticity for the material b) The proportional limit c) The ultimate stress Show a complete solution
Question One Figure Q1 shows a stress state element in a material component. Analyse the element and calculate the principal stresses and positions of the principal planes in the component, using: Solve through Mohr 1.2 circle on graph paper 120 MPa 25 MPa 80 MPa Figure Q1.
In a tensile test for an aluminum alloy, the sample used is 2 inches long and 0.5 inches in diameter. The proportional portion of the tension stress-strain diagram for an aluminum alloy is shown below. Determine the modulus of elasticity for this material: ____x106 lb/in2. Pay attention to units and calculate your answer to 1 decimal place for the unit specified above.
The strains on the surface of an experimental device made of steel (E = 200 GPa and v = 0.33) and tested in a space shuttle were measured by means of strain gages. The gages were oriented as shown in the figure, and the measured strains were €4 = 1,100 x 10-6, Eg = 1,434 x 10-6, Ec = -36.76 x 10-8 What is the stress oz in the e direction? Round to two decimal places. MPa
8. The strain components Ex, Ey, and Yxy are given for a point in a body subjected to plane strain. Determine the strain components &n, E, and y at the point if the n-t axes are rotated with respect to the x-y axes by the amount and in the direction indicated by the angle 9 shown in Fig. 8. Sketch the deformed shape of the element. &x=+520 με, &y=-650 μ, Yxx = +750 μrad, 0 = 35° Fig. 8
Take o,= 120 kPa and o, = 630 kPa Determine the equivalent state of stress on an element at the same point that represents the maximum in-plane shear stress at the point. (Figure 1) Figure K 1 of 1 Oy 400 kPa Part A Find the value of Tmax in-plane- Express your answer to three significant figures and include the appropriate units. µA Tmax in plane = Value Units Submit Request Answer Part B Find the value of oavg Express your answer to three significant figures and include the appropriate units.
QUIZ · Example I: Given the following state of stress and material properties Ox = 10MPa E = 200GPA Tyx 0z = -15MPA v =0.2 Tyz = 5MPA · Determine the state of strain - Determine the change in volume (also known as volumetric strain or dilatation)