Еxample The following information obtained in tension test on a material as the sectional area of the sample is 50 mm and length 1000 mm, draw the stress strain curve and then determine the value of proportional limit, yield stress and ultimate strength, failure stress and modulus of elasticity. Load(KN) 10 20 30 40 42 42.5 42.8 43 43.2 Extension(mm) 5 10 15 20 25 30 33 36 40 Load(KN) 44 46 50 54 55 53 50 46 43 Extension(mm) 45 50 60 80 100 120 136 150 160

Еxample The following information obtained in tension test on a material as the sectional area of the sample is 50 mm and length 1000 mm, draw the stress strain curve and then determine the value of proportional limit, yield stress and ultimate strength, failure stress and modulus of elasticity. Load(KN) 10 20 30 40 42 42.5 42.8 43 43.2 Extension(mm) 5 10 15 20 25 30 33 36 40 Load(KN) 44 46 50 54 55 53 50 46 43 Extension(mm) 45 50 60 80 100 120 136 150 160

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

PROBLEMS 203. During a stress-strain test, the unit deformation at a stress of 5000 psi Wap ODserved to be 0.000167 in./in. and at a stress of 20,000 psi it was 0.000667 in./in. If the proportional limit is 30,000 psi, what is the modulus of elasticity? What is the stress corresponding to a strain of 0.0002 in./in.? Would these re- sults be valid if the proportional limit were 18,000 psi? Explain. E = 30 X 106 psi; S 6000 psi %3D Ans. 204. A uniform bar of length L, cross-sectional area A, and weight W is sus- WL If pended vertically from one end. Show that its total elongation is & = 2AE wL? its weight per unit volume is w, show also that & 2E A steel rod having a cross-sectional area of sq in. and a length of 600 ft is suspended vertically. It supports a load of 5000 lb at the lower end. If steel 30 X 106 psi, find the total elongation in the rod. Ans. 8 = 2.64 in. 205 weighs 490 lb/cu ft and E Hint: Use the result of Prob. 204. steel wire 30 ft long, hanging vertically, supports a…
The nominal stress-strain diagram for a specimen having an original diameter of 10 mm and a gauge length of 50 mm is shown below. Using the given nominal stress-nominal strain diagram, answer this question. The inset shows a detailed view of the curve at low strains. 400 350 300 250 Stress (MPa) 200 150 100 50 0 0.00 Stress (MPa) 350 kN 300 250 200 150 100 50 0 0.000 0.002 0.004 0.006 0.008 0.010 0.012 Strain 0.02 0.04 0.06 0.08 0.10 0.12 0.14 0.16 Strain 0.18 What is the maximum force that could be applied to the specimen before it plastically deforms?
1. If we take the stress function = 2x²y + xy², what are the stress components according to this stress function? What are the stresses on the boundaries of the body below? O y H H L X
Give me right solution
650 600 550 500 450 400 350 300 250 200 150 100 50 0.002 0.004 0.006 0.008 0.01 0.012 0.014 0.016 0.018 0.02 Strain mm/mm The graph above shows the stress-strain relationship of a steel bar under tension test. The steel bar diameter = 8 mm and the bar gauge length = 100 mm. Determine the following: Toughness of the specimen Stress (MPa)
The tensile test has been performed on a 50 mm long steel tube having 18 mm external diameter and 12 mm internal diameter. The axial load of 2 kN produced a stretch of 3.36 x 10-³ mm and a lateral contraction of the outer diameter of 3.62 x 104 mm. Calculate Young's modulus, Poisson's ratio and bulk modulus for the material
At a point in a machine component that is subjected to plane stress, the normal and shear stresses are o, = 60 MPa, o, = 110 MPa, and Txy = 28 MPa, acting in the directions shown in the figure. At this point, determine the strain components &x, y, z, and Yxy. Assume that E = 73 GPa and v=0.29 for the machine component. £x = que 11 Ox Ez = με με με μrad
* Your answer is incorrect. A solid plastic rod has a diameter of d = 21 mm and a length of L = 600 mm. An axial load of P = 24 kN is applied to the rod as shown. The elastic modulus is E = 2.6 GPa and Poisson's ratio for this material is v= 0.37. Determine the magnitude of the change in the rod diameter Ad for the given load. Answer: Ad= i -0.21 L mm
Situation 8: The rigid, horizontal slab is attached to two identical copper rods. There is agap A = 0.08 mm between the middle bar, which is made of aluminum, and the slab.Neglecting the mass of the slab, the temperature in in all rods by 60°C. Use the following data: Each bronze rod Aluminum rod 22. Compute the stress in bronze rod 23. Compute the stress in aluminum rod 24. Compute the deflection on the rods Bronze A (mm²) 650 480 A Aluminum a (/°C) 18.9 x 10-6 23.1 x 10-6 Bronze 850 mm E (GPa) 83 70
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3⁄8 inch and the gage length (the length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress–strain data and draw a best-fit curve. c. Compute the modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress