The nominal stress-strain diagram for a specimen having an original diameter of 10 mm and a gauge length of 50 mm is shown below. Using the given nominal stress-nominal strain diagram, answer this question. Theinset shows a detailed view of the curve at low strains.400350300250Stress (MPa)2001501005000.00Stress (MPa)350kN3002502001501005000.000 0.002 0.004 0.006 0.008 0.010 0.012Strain0.02 0.04 0.06 0.080.10 0.12 0.14 0.16Strain0.18What is the maximum force that could be applied to the specimen before it plastically deforms?

Given data The nominal stress strain graph has been given The diameter of the specimen (d) = 10 mm…

The nominal stress-strain diagram for a specimen having an original diameter of 10 mm and a gauge length of 50 mm is shown below. Using the given nominal stress-nominal strain diagram, answer this question. The inset shows a detailed view of the curve at low strains. 400 Stress (MPa) 350 350 300 250 200 €200 C 150 150 100 50 0 0.000 0.002 0.004 0.006 0.008 0.010 0.012 Strain 0.02 0.04 0.06 0.08 0.10 0.12 0.14 0.16 300 250 100 50 0. 0.00 0.18 Strain What is the maximum force that could be applied to the specimen before it plastically deforms? KN

The nominal stress-strain diagram for a specimen having an original diameter of 10 mm and a gauge length of 50 mm is shown below. Using the given nominal stress-nominal strain diagram, answer this question. The inset shows a detailed view of the curve at low strains. 400 Stress (MPa) 350 350 300 250 200 €200 C 150 150 100 50 0 0.000 0.002 0.004 0.006 0.008 0.010 0.012 Strain 0.02 0.04 0.06 0.08 0.10 0.12 0.14 0.16 300 250 100 50 0. 0.00 0.18 Strain What is the maximum force that could be applied to the specimen before it plastically deforms? KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

From the given illustration below, the force acting on B is equal to 25 kN, on C = 20 kN, and on D = 30 kN. If the cross sectional area of the material is 600 sg.mm, what is the maximum stress in the bar? FINAL EXAM 一- A B FINAL EXAM
PROBLEMS 203. During a stress-strain test, the unit deformation at a stress of 5000 psi Wap ODserved to be 0.000167 in./in. and at a stress of 20,000 psi it was 0.000667 in./in. If the proportional limit is 30,000 psi, what is the modulus of elasticity? What is the stress corresponding to a strain of 0.0002 in./in.? Would these re- sults be valid if the proportional limit were 18,000 psi? Explain. E = 30 X 106 psi; S 6000 psi %3D Ans. 204. A uniform bar of length L, cross-sectional area A, and weight W is sus- WL If pended vertically from one end. Show that its total elongation is & = 2AE wL? its weight per unit volume is w, show also that & 2E A steel rod having a cross-sectional area of sq in. and a length of 600 ft is suspended vertically. It supports a load of 5000 lb at the lower end. If steel 30 X 106 psi, find the total elongation in the rod. Ans. 8 = 2.64 in. 205 weighs 490 lb/cu ft and E Hint: Use the result of Prob. 204. steel wire 30 ft long, hanging vertically, supports a…
Can I get a step by step walkthrough?
Minimum of 3 decimal places in all computations.
Give me right solution
650 600 550 500 450 400 350 300 250 200 150 100 50 0.002 0.004 0.006 0.008 0.01 0.012 0.014 0.016 0.018 0.02 Strain mm/mm The graph above shows the stress-strain relationship of a steel bar under tension test. The steel bar diameter = 8 mm and the bar gauge length = 100 mm. Determine the following: Toughness of the specimen Stress (MPa)
At a temperature of 27.89 °C a 0.41-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 126.64°C, determine the magnitude of the normal stress (in MPa) in the steel rod if L = 320.36 mm and M = 231 mm. Round off the final answer to four decimal places. d ... M A B Aluminum Stainless steel A = 2000 mm² E = 75 GPa a = 23 × 10-6/C A = 800 mm² E = 190 GPa %3D a = 17.3 × 10-6/°C
At a point in a machine component that is subjected to plane stress, the normal and shear stresses are o, = 60 MPa, o, = 110 MPa, and Txy = 28 MPa, acting in the directions shown in the figure. At this point, determine the strain components &x, y, z, and Yxy. Assume that E = 73 GPa and v=0.29 for the machine component. £x = que 11 Ox Ez = με με με μrad
COMPLETE SOLUTIONS PLEASE WITH FBD
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3⁄8 inch and the gage length (the length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress–strain data and draw a best-fit curve. c. Compute the modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress
A brass alloy rod having a cross sectional area of 0.24 in.2and a modulus of 16 * 106 psi is subjected to a tensile load. Plastic deformation was observed to begin at a load of 8,944 lb.a. Determine the maximum stress that can be applied without plastic deformation.b. If the maximum length to which a specimen may be stretched without causing plastic deformation is 3.28 in., what is the original specimen length?