Consider a metal bar 12.5 mm in diameter and 50 mm in length that is tested under uniaxial tension. The test results data are as follows: Force (kN) Final length (mm) Final diameter (mm) 122 56,14 12,19 120 62,05 11,60 114 68,57 11,03 (a) Complete the following table: Force (kN) Final length (mm) Final diameter (mm) True stress (MPa) True deformation (mm/mm) 122 56,14 12,19 120 62,05 11,60 114 68,57 11,03 (b) Determine the metal's work hardening coefficient. (c) The most likely crystal structure for this metal is?

Consider a metal bar 12.5 mm in diameter and 50 mm in length that is tested under uniaxial tension. The test results data are as follows: Force (kN) Final length (mm) Final diameter (mm) 122 56,14 12,19 120 62,05 11,60 114 68,57 11,03 (a) Complete the following table: Force (kN) Final length (mm) Final diameter (mm) True stress (MPa) True deformation (mm/mm) 122 56,14 12,19 120 62,05 11,60 114 68,57 11,03 (b) Determine the metal's work hardening coefficient. (c) The most likely crystal structure for this metal is?

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.3P: A tensile test was performed on a metal specimen having a circular cross section with a diameter 0....

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
COMPLETE SOLUTIONS PLEASE WITH FBD
Mechanical properties of materials • H.W.: • The following data where obtained during the tensile test of mild steel circular bar 12.75 mm diameter and 203.2 mm gauge length. Determine the following: 1) The apparent stress at each point 2) Strain at each point 3) True stress at each point (Assume D at failure is 8,51 mm and D at max. load is 11.15 mm) 4) Draw stress - strain curved based on: a) Original cross sectional area b) True cross sectional area 5) Proportional limit Mechanical properties of materials 6) Modulus of elasticity 7) Upper and lower yield point 8) Ultimate strength 9) Breaking strength based on the original cross sectional area and on true cross sectional area 10) Percentage of elongation 11) Percentage of reduction in cross sectional area. 12) Ductility, Resilience and toughness Load (N) 4393 16902 29357 33360 33627 35584 41366 48839 52709 55378 56356 43768 Deformation 0.0254 0.127 0.228 0.305 0.356 3.81 6.35 11.68 16.76 26.92 43768 42.42 (mm )
solve the given problem and show complete fbd and geometry of deformation
Question 8 The rigid, horizontal slab is attached to two identical copper rods. There is a gap A = 0.18 mm between the middle bar, which is made of aluminum, and the slab. Neglecting the mass of the slab, calculate the stress in each rod when the temperature in the assembly is increased by 85 °C. Use the following data: A (mm?) a (C) E (GPa) Each copper rod 500 16.8 x 10-6 120 Aluminum rod 400 23.1 x 10- 70 Copper unusunjv Copper 750 mm-
An aluminum tube has an outside diameter of 2.5 inches will be used to support 27 kips of load. If the normal stress in the member must be limited to 18 ksi, how thick in inches should the aluminum be? Note: Draw the Free Body Diagram, include the units/dimensions, use the proper formula and round-off all the answers and final answers to 3 decimal places.
Part 2
Please answer correctly and box the final answer.
A cylindrical specimen of 1018 steel having a diameter of 6.35 mm and a gauge length of38.1 mm is pulled in tension. Use the load-elongation characteristics tabulated below. Determine the yield strength (σy) at a strain offset of 0.002.
A cylindrical specimen of aluminum alloy having a diameter of 12.8 mm and a gauge length (lo) of 50.800 mm is pulled in tension. Use the load–elongation characteristics shown in the following table and answer the following questions. (10p) i- Convert the data as engineering stress (σ) versus engineering strain (ε). ii- Compute the modulus of elasticity (E) (with a precision of ±5000 MPa) iii- Determine the yield strength at a strain offset of 0.002 (σy) (with a precision of ±20 MPa) iv- Determine the tensile strength (TS) of this alloy.
A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure. Axial loads are applied at the positions indicated. If P 4000 Ib and the cross-sectional area of the rod is 1.0 sq.in. What is %3D the stress in the bronze? (in ksi) Note: indicate sign (no sign means positive/tenslon) 4P Steel Bronze Aluminum 2 ft 3 ft 2.5 ft