2. Given that a steel cylinder of dimenslons 12.0 mm in dlameter and 70 mm long is subjected totensicn.(a) Determine the modulus of elasticity in the figure below.(b) Using the figure below, calculate the deformation in the steel cylinder subjected to 15 kNtension for ce.600500400500400E3003002002001001000.0000.0020.0040.006Strain8.000.040.030.120.160.20StrainTensile stress-strain behavior for a steel alloy.Daccri be io v ourMP MOrds the throo ctrongthanin garnin cize rad uction colidStress (MPa)Stress (MPa)

a) According to Hook's law within the elastic limit, stress is directly proportional to strain.…

Given that a steel cyInder of dimenslons 12.0 mm in dlameter and 70 mm bng is subjected to tensicn. (a) Determine the modulus of elastidity in the figure below. (E) Using the figure below, calculate the deformation in the steel cylinder subjected to 15 kN tension for e. 600 500 400 500 400 300 300 200 200 100 100 S000 0.002 0.004 0.006 Strain 8.00 0.04 0.20 0.08 0.12 0.16 Strain Tensile stress-strain behavior for a steel alloy. Sress (MPa) Stress (MPa)

Given that a steel cyInder of dimenslons 12.0 mm in dlameter and 70 mm bng is subjected to tensicn. (a) Determine the modulus of elastidity in the figure below. (E) Using the figure below, calculate the deformation in the steel cylinder subjected to 15 kN tension for e. 600 500 400 500 400 300 300 200 200 100 100 S000 0.002 0.004 0.006 Strain 8.00 0.04 0.20 0.08 0.12 0.16 Strain Tensile stress-strain behavior for a steel alloy. Sress (MPa) Stress (MPa)

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.2DP

See similar textbooks

Similar questions

4.20 A cylindrical aluminum alloy rod with a 0.5 in. diameter is subjected to ten- sion. Determine the magnitude of the load required to produce a 10 in. change in diameter if the deformation is entirely elastic. Assume a Young's modulus of 11 X 106 psi and a Poisson's ratio of 0.33.
Please answer letters a, b, c and d. Thank you!
Part 2
) Consider a cylindrical specimen of a steel alloy 10.0 mm in diameter and 75 mm long that is pulled in tension. (a) Determine its elongation when a load of 20,000 N is applied. (b) What is the modulus of elasticity? (c) What is the strength at a strain offset of 0.002? (d) What is the tensile strength?
2. A steel bar, whose cross section is 0.55 inch by 4.05 inches, was tested in tension. An axial load of P = 30,500 lb. produced a deformation of 0.105 inch over a gauge length of 2.05 inches and a decrease of 0.0075 inch in the 0.55-inch thickness of the bar. Determine the lateral strain. * Your answer Determine the axial strain. Your answer Determine the Poisson's ratio v. * Your answer Determine the decrease in the 4.05-in. cross-sectional dimension (in inches). * Your answer
A round steel alloy bar with a diameter of 19 mm and a gauge length of 76 mm was subjected to tension, with the results shown in Table P3.26. Using a computer spreadsheet program, plot the stress-strain relationship. From the graph, determine the Young's modulus of the steel alloy and the deformation corresponding to a 37 kN load. TABLE P3.26 Deformation, Load, kN mm 9 0.0286 18 0.0572 27 0.0859 36 0.1145 45 0.1431 54 0.1718
The figure above are two rods attached to a rigid bar AB with negligible mass . A 68kN load was applied at the end of this bar. The computed stresses for steel and bronze are GIVEN THAT MN=68kN
2. A steel bar, whose cross section is 0.55 inch by 4.05 inches, was tested in tension. An axial load of P = 30,500 lb. produced a deformation of 0.105 inch over a gauge length of 2.05 inches and a decrease of 0.0075 inch in the 0.55-inch thickness of the bar. * Determine the lateral strain. Your answer Determine the axial strain. Your answer Determine the Poisson's rati v. Your answer Determine the decrease in the 4.05-in. cross-sectional dimension (in inches). * Your answer
A 220 mm? steel rod and 420 mm? copper rod supports a rigid bar as shown. If a 30 kN load is attached at the far end of the bar, determine the stresses in each of the rods. Based on the laboratory results, E= 200 GPa for steel and E= 100 GPa for copper. Show the free-body diagram. COPPER STEEL 2 m m- 2 m Hm- 30 kN
S Figure P1.16 shows the stress-strain relations of metals A and B during ten- sion tests until fracture. Determine the following for the two metals (show all calculations and units): a. Proportional limit b. Yield stress at an offset strain of 0.002 m/m. c. Ultimate strength d. Modulus of resilience e. Toughness f. Which metal is more ductile? Why? 900 Metal A 600 Metal B 300 0.00 0.02 0.04 0.06 0.08 0.10 0.12 0.14 Strain, m/m FIGURE P1.16 Stress, MPa
The state of stresses in the x and y directions at a point in a given material is shown in the figure below. If the value of the shear stress in the x-y axes Ty is 17N/mm2, find the maximum shear stress that can be found at this point in any possible direction. Round off your answer to the nearest N/mm2. 10 N/mm2 Txy 20 N/mm2 20 N/mm2 Txy 10 N/mm2
Based on the figure below, a steel rod was fitted on the copper tube and was fixed with a washers and tightened with nuts with an applied force of MN kN. Calculate the working stress of the rod and tube if the temperature during the fitting is 48 degrees Celsius. Modulus of Elasticity of Steel = 200 GPa Modulus of Elasticity of Copper = 100 Gpa Coefficient of Expansion due to Temperature of Steel = 12 x 106 / °C Coefficient of Expansion due to Temperature of Copper = 18 x 106 / °C FN=70 MN=76 SN=50 Steel 20 mm