Answered: In the figure shown below, determine:…

In the figure shown below, determine: 1) The final temperature if the normal stress at aluminium is oal = -90 MPa and the initial temperature 20°C. 2) The final length of the aluminium member.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The elongation of a bar in axial loading is proportional to the following except A Stress in the bar…

Q: why is P positive for stress A

A: The compressive stress is considered as positive and tensile stress is considered as negative.

Q: A 300 mm Long copper wire of uniform cross-section is pulled in tension so that a maximum tensile…

A: Given data : Length of copper wire = 300 mm Max. tensile stress = 270 MPa The elastic modulus of…

Q: Example: the low cycle fatigue of a certain steel is given by life cycle equation-2: (of/E)=0.005…

A: The fatigue strength of steel /Modulus of elasticity(E), The fatigue Ductility coefficient is, The…

Q: The radius of Mohr's circle of stress of a strained element is 20 N/mm² and minor principal tensile…

A: Given- Radius of Mohr's circle R=20 N/mm2Minor principal tensile stress =10 N/mm2

Q: The minimum strain at failure in tension steel having yield stress modulus E = 200 GPa, as per Limit…

Q: B. C E Strain FIGURE Q1 (a) Stress -

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 840 mm.…

Q: A sheet of copper is stretched biaxially in the xy-plane. If the strains in the sheet are ϵx = 0.40…

A: given data:

Q: Fc FA Fa Fc

A: According to given data Fa , Fb , Fc principal stresses are shown in three elements We need to…

Q: At room temperature (200C) a 0.50mm gap exists between the ends of the rods shown. At a later time…

Q: The value of strain if stress is 35 MPa and Youngs modulus 65 MPа

A: The given question is related with solid mechanics . In this question we are provided with value of…

Q: The brass shell (ab = 20.9 × 10-6/°C) is fully bonded to the steel core (as = 11.7 × 10-6°C).…

A: Step 1:Step 2:

Q: Materials can have different masses but equal volumes. a. TRUE b. FALSE

A: Density : It is the ratio of mass and volume . Mass : it defines about how much matter an object…

Q: With the help of a diagram, contrast the stress-strain relationship with respect to ceramic and…

A: Metals are usually hard, opaque, shiny, and have sensible electrical and thermal conductivity.…

Q: A tensile force of 5 kN produce an elastic reduction in diameter of 4 x 10-4 mm on a metal alloy…

A: given data: Force (F)=5 KNdiameter (d)=6 mmreduction in diameter(∆d)=4×10-4 mm

Q: A steel plate is bent into a circular arc of radius 10 m. If the plate section be 120 mm wide and 20…

Q: Calculate the mass of each sphere. Assume a = 4.9, b = 2.3, 0=29. y 1 R aR Titanium Answers:…

Q: A 2-ft rod with a modulus of elasticity of 8840 ksi, is subjected to a tensile force of 1000 lb and…

Q: Find the value of strain if stress is 50 MPa and youngs modulus is 100 MPa

A: The strain can be calculated using Hookes law.

Q: TRUE STRESS STRAIN CUI

A: A stress-strain curve for a material is used in engineering and materials science to show the…

Q: The deformation per unit length is called C(A) Tensile stress O(B) Compressive stress OCC) Shear…

A: Strain : Strain is defined as the ratio of change in length upon original length , It is…

Q: Two triangular wedges are glued together as shown in the following figure. The stress acting normal…

A: Given- Stresses- σx=+100 MPa,σy=-100 MPa,angle θ=45o, It is needed to find the value of the normal…

Q: In the strain hardening regi happens if the stress is reme

Q: The aluminum shell is fully bonded to the brass core, and the assembly is unstressed at a…

Q: A 2 m long, axially loaded mild steel rod of 8 mm diameter exhibits the load- 14000 12000…

A: A graph of displacement against load, yield stress, length of mild steel rod, Diameter have been…

Q: The rigid bar is supported by a pin at A and two metal wires, each having a diameter of 4 mm. The…

Q: Within elastic limit, stress is O(A) Inversely proportional to strain O(B) Directly proportional to…

A: Hooks law: Within elastic limit stress is directly proportional to strain . It means the deformation…

Q: Permanent deformations in structures refer to: A. linear elastic deformations B. deflection diagram…

A: The study of temporary or elastic extraction in the field of engineering is applied to materials…

Q: Stresses that cause change in volume are called (A) hydrostatic stresses B deviatoric stresses…

A: We need to choose correct option based on given choices

Q: b1 Answer: 1= i 648.03 N-m Save for Later Last saved 2 hours ago. Attemnt

Q: Calculate Young's modulus for an iron crystal when tension is applied along [2 -2 1] direction.…

A: S11 = 7.6(TPa)-1 S12 = 2.8(TPa)-1 S44 = 8.6(TPa)-1

Q: For the figure shown, if the stress in steel is 75 MPa, then the stress in the ****** .. copper is…

A: Given data in question Stress in steel Elasticity modulus To find out Stress in copper

Q: Draw a tensile stress-strain curve for a typical semi-crystalline polymer such as LLDPE, and define…

Q: A component made of Aluminium 6061-T651 has an edge crack with length equal to 15 mm, as shown The…

Q: Tim In the yielding region, what happens if the stress is removed? O a. The material does not return…

Concept explainers

Properties of materials

A property of a material describes its characteristics and distinguishes it from the others. The material properties are described it in terms of its hardness, color, appearances, and so on. The material properties generally depend on the type of material, or whether it is a metal or an alloy. There are different kinds of material properties such as mechanical properties, thermal properties, physical properties, and chemical properties. Chemical properties describe the material in terms of a chemical change. The mechanical properties come into existence when the material is acted upon by an external load. Thermal properties are associated with the temperature of the material and specific heat.

Question

100%

In the figure shown below, determine:
1) The final temperature if the normal stress at aluminium is oal =
-90 MPa and the initial temperature 20°C.
2) The final length of the aluminium member.
Aluminum
A=1800mm?
E=73GPA
Bronze
A=1500mm2
E=105GPA
a=23.2x10-6/°C
a=21.6x10-6/°C
Gap=0.5mm
0.35m
0.45m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Given Data.

VIEW

Find the final temperature.

VIEW

Find the final length of Al bar.

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

If it is constrained between two supports A and B and is stress-free at 20 ℃, what would be the stress in the two materials when it is heated to 70 ℃, For Steel: Es = 210 GPa, Coefficient of expansion = 12x10^6/℃. For Brass: Eb = 105 GPa, Coefficient of expansion = 19x10^-6/℃
-6 The aluminum shell is fully bonded to the brass core and the assembly is unstressed at a temperature of 16°C. It is known thatE = 105 GPa and a = 20.9 × 10 °C for the brass core and E = 71 GPa and a = 23.8 × 10¯6°C for the aluminum shell. Considering only axial deformations, determine the stress in the aluminum when the temperature reaches 185°C. 25 mm σα MPa -63 mm
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 760 mm. The cross-sectional dimensions of the beam are b1 = 33 mm, d1 = 110 mm, b2 = 20 mm, d2 = 20 mm, and a = 6.5 mm. For this material, the allowable tensile bending stress is 11 MPa, and the allowable compressive bending stress is 12 MPa. Determine the largest moment M that can be applied as shown to the beam.
The degree to which the theoretical value of stress concentration is actually reached is called as
The lowest stress at which permanent .deformation can be measured
An element in the plane stress is having the larger principal stress (tension) as 30 MPa and it is subjected to stresses, Ox = 50 MPa, 40 MPa then what will be and Txy the value of the stress oy? (in MPa) =
6
1 It is the ratio of ultimate tensile stress to the permissible stress. Plastic Shear Plastic limit Proportional limit Factor of safety Poisson's ratio
At room temperature (20°C) a 0.7-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 150°C, determine: (a.)The normal stress in the aluminum rod, (b.) The change in length of the aluminum rod. 0.7 mm 300 mm A Aluminum A =2,000 mm² E= 75 GPa α = 23 x 106/°C 250 mm B Stainless steel A = 800 mm² E = 190 GPa a = 17.3 x 10-6/°C
At a certain point in a structural member, the value of ox = -45 N/mm², ay = 75 N/mm² and t = 45 N/mm2. The principal stresses will be
Two triangular wedges are glued together as shown in the figure. The stress acting normal to the interface, o, is MPa. 100 MPa 100 MPa on 45% 100 MPa -100 MPa