For the figure shown, if the stress insteel is 75 MPa, then the stress in thecopper isCopperrodE=120GPaSteeltubeE=200GPa55 MPa O35 MPa O65 MPa O45 MPa O25 MPa O

Given data in question Stress in steel Elasticity modulus To find out Stress in copper

Answered: For the figure shown, if the stress in…

For the figure shown, if the stress in steel is 75 MPa, then the stress in the ****** .. copper is Copper rod L E=120 GPa 55 MPa O 35 MPa O 65 MPa 45 MPa Steel tube E=200 GPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. The column in the figure shown has a strain on its compressive edge equal to -0.003 and has a tensile strain of +0.00185 on its other edge. Detemine the nominal values of Pn and Mn that cause this strain distribution if f'c = 21 MPa, fy = 414 MPa. Draw the column interaction diagram. en 600 Pn mm 8 - 6 32mm 75 225 225 75 600
A steel bar 100 mm long is subjected to a tensile stress o. If change in length of bar is 0.05 mm what is the value of o? Given E = 200 GPa
2. Solve for the deformation of the aluminum rod. 200 mm 300 mm 600 kN Aluminum E= 70 GPa A= 900 mm Steel E= 200 GPa A=1200 mm
Problem # 2. At room temperature (20°C) a 0.5-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 140 °C, determine (a) the normal stress in the aluminum rod Ans: A -300 mm Aluminum A = 2000 mm² E = 75 GPa α = 23 x 16-6/°C 0.5 mm -250 mm Stainless steel A = 800 mm² B E = 190 GPa a = 17.3 x 10-6/°C
An aluminum plate is subjected to uniform stress along its boundaries, as shown in the figure. Determine the change of length of diagonal BD. 120mm 120 MPa 160mm , 100мра C 240 MPa E=80GPa ✓=0.3 G=30GPa Answer = -0.5888mm
An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown below. Axial loads are applied at the positions indicated. Find the maximum value of P in Newton that will not exceed a stress in steel of 150 MPa, in aluminum of 87 MPa, or in bronze of 97 MPa.
The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar (1) is a bronze alloy [E = 102 GPa] with a cross-sectional area of A₁ = 200 mm². Bar (2) is an aluminum alloy [E = 72 GPa] with a cross-sectional area of A₂ = 640 mm². All bars are unstressed before the load P is applied; however, there is a 2-mm clearance in the pin connection at A. Assume L₁ = 1880 mm, a = 1060 mm, b = 620 mm, c = 480 mm, and L₂ = 1270 mm. If a load of P = 71 kN is applied at B, determine (a) the normal stresses in both bars (1) and (2). (b) the downward deflection of point A on the rigid bar. (1) L₁ b tc B (2) D L2
An element in the plane stress is having the larger principal stress (tension) as 30 MPa and it is subjected to stresses, Ox = 50 MPa, 40 MPa then what will be and Txy the value of the stress oy? (in MPa) =
A rigid bar of negligible weight is supported and loaded with 70 kN, compute the temperature change AT (°C) that will cause the stress in the bronze rod (L = 1.5 m, A = 300 mm?, and E = 83 GPa) to be 50 MPa. Assume a = 18.9 µm/(m°C) for bronze and 12.8 um/(m°C) for aluminum (L = 3 m, A = 750 mm2, and E = 70 GPa). Aluminum Bronze 2.5 m 1.5 m 70 kN
3. An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 13.05 ksi, or in bronze of 100 MPа. Aluminum A = 400 mm? Bronze A = 200 mm Steel A = 500 mm? 2P 4D 2.5 m 2.0 m 1.5 m
Problem 1 An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Aluminum Steel A=800mm2 A=1000mm2 Bronze A=700mm? 4P 2P 500mm 600mm 700mm 1. What is the maximum value of P that will not exceed the axial stress bronze of 105 MPa? 2. What is the maximum value of P that will not exceed the axial stress in aluminum of 90 MPa? 3. If P=10KN, what is the axial force to be carried by the aluminum in KN? 4. If P is 5KN, what is the axial stress of steel?
Narrow bars of aluminum are bonded to the two sides of a thick steel plate as shown. Initially, at T₁ = 70°F, all stresses are zero. Knowing that the temperature will be slowly raised to T₂ and then reduced to T₁, determine (a) the highest temperature T₂ that does not result in residual stresses, (b) the temperature T₂ that will result in a residual stress in the aluminum equal to 58 ksi. Assume aa = 12.8 x 10-6/°F for the aluminum and a = 6.5 × 10-6/°F for the steel. Further assume that the aluminum is elastoplastic with E = 10.9 × 106 psi and ay = 58 ksi. (Hint: Neglect the small stresses in the plate.) Fig. P2.121