The rigid bar of negligible weight is supported as shown in the figure. If W = 80 kN, compute t emperature change of the assembly that will cause a tensile stress of 50 MPa in the steel rod. Use t ollowing data: A (in?) a (/OF) E (GPa) Steel Rod 300 11.7 x 106 200 Bronze Rod 1400 18 x 10-6 83 Bronze 3 m

The rigid bar of negligible weight is supported as shown in the figure. If W = 80 kN, compute t emperature change of the assembly that will cause a tensile stress of 50 MPa in the steel rod. Use t ollowing data: A (in?) a (/OF) E (GPa) Steel Rod 300 11.7 x 106 200 Bronze Rod 1400 18 x 10-6 83 Bronze 3 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The failure stress of a homogeneous steel bar having a diameter of 10 mm is 250 MPa. Using a factor of safety of 2.0, calculate the maximum load in N that the bar can support. А) 12500-pi в) 6250*pi с) 3125*pi D) 1563*pi
A bronze pipe (1) is to be connected to an aluminum alloy pipe (2) at flange B. When put in place, however, a gap of A = 0.25 in. exists between the two pipes. Bronze pipe (1) has an elastic modulus of E, = 16,000 ksi, a cross-sectional area of A, = 2.83 in.?, and a length of L1 = 6.9 ft. Aluminum alloy pipe (2) has an elastic modulus of E2 = 10,000 ksi, a cross-sectional area of A2 = 1.47 in.2, and a length of L2 = 12.0 ft. If bolts are inserted in the flanges and tightened so that the gap at B is closed, determine: (a) the normal stresses produced in each of the members. (b) the final position of flange B with respect to support A. L2 В (1) Answer: (a) σ1- ksi 02 = ksi (b) OB/A = in.
A rigid bar ABCD is supported by two bars as shown in the figure. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in rod (1) is -1350 µm/m. Determine the normal strain in rod (2) if there is a 1-mm gap in the connection at pin C before the load is applied. A 240 mm B (1) O 1281 um/m O 1877 µm/m O 1141 µm/m O 1358 µm/m O 999 µm/m 360 mm (2) Rigid bar 900 mm C 140 mm, 1,500 mm
Determine the normal stress in the steel plate. Gusset plate is 16 mm thick column pin diameter = 20 mm gusset plate steel plate 70 kN pin 60mm 8-mm plate thickness 183.45 MP 0148.53 MPa 58.33 MP3 22282 MP A 14583MP
Determine the normal stress in members BD, AC, and BCin the truss shown. The cross-sectional area of each member is 1500mm2. Indicate whether the stresses are tensile (T) or compressive (C). Use 2 decimal places in every solved value.
A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between them which is 699.93 mm long. If the allowable stresses are Salum = 90 MPa and Spronze=80 MPa, find the maximum weight of the beam that the system can support (in KN). note: please help us in this sample question and it is not a graded question but a practice question thank you
fast
The beam is subjected to a loading condition as shown in th figure. Determine the (a) maximum tensile stress and (b) maximum compressive stress with the givenm cross section. Show you complete solution and diagram.
Q19: In Figure below, what is the ratio of P to F h Waer Hinge Sec A-A
For the assembly shown in the figure below, Determine the state of stress at point A on the cross section of the pipe at section a-a. 20 mm P 170N d 30mm Section a-a 120mm b 220mm