Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an internalA,Bpressure, and a torque. In points A and B, the following stresses occur due to the loading: o63.5 MPa, B=127 MPa, T = 127 MPa=a. Determine omin, omax, and its direction (in degrees) from x-axis at point A.b. Determine omin, omax, and its direction (in degrees) from x-axis at point B.1BxCOOOA

Answered: Image /qna-images/answer/3ab2e246-7724-4b2b-b4b5-c53272158c96.jpg

Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an internal pressure, and a torque. In points A and B, the following stresses occur due to the loading: 63.5 MPa, B=127 MPa, T = 127 MPa A.B = a. Determine omin, omax, and its direction (in degrees) from x-axis at point A. b. Determine Gmin, Gmax, and its direction (in degrees) from x-axis at point B. I B O A

Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an internal pressure, and a torque. In points A and B, the following stresses occur due to the loading: 63.5 MPa, B=127 MPa, T = 127 MPa A.B = a. Determine omin, omax, and its direction (in degrees) from x-axis at point A. b. Determine Gmin, Gmax, and its direction (in degrees) from x-axis at point B. I B O A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In the figure shown, the AB part of the rod is made from brass while the BC part is fabricated from aluminium, both parts are restrained at the ends. Find: 1) The normal stresses OAB and OBC + when the temperature is increased to 42°C. 2) The deflection at point B (8B) Brass: ab=20.9*10-6 1/°C, Eb=105GPA Aluminum: aa=23.9*10-6 1/°C, Eal=72GPA //// A 60 mm diameter 1.1 m B 40 mm diameter 1.3 m Aluminum Brass
Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an internal pressure, and a torque. In points A and B, the following stresses occur due to the loading: o 63.5 MPa, B=127 MPa, = 127 MPa A.B A.B a. Determine Gmin, omax, and its direction (in degrees) from x-axis at point A. b. Determine omin, omax, and its direction (in degrees) from x-axis at point B. 1 B d O A x
1) The head H is connected to the cylinder of a compressor using six steel bolts. If the clamping force in each bolt is 4000N, determine the normal strain in the bolts. Each bolt has a diameter of 5 mm. If o₂ = 280 MPa and Est = 210GPa, what is the strain in each bolt when the nut is unscrewed so that the clamping force is released? a) 0.970 b) 0.203 c) 0.970(10-³) d) Insufficient information to determine because the stress is beyond yield point H &
The failure stress of a homogeneous steel bar having a diameter of 10 mm is 250 MPa. Using a factor of safety of 2.0, calculate the maximum load in N that the bar can support. А) 12500-pi в) 6250*pi с) 3125*pi D) 1563*pi
(40 How A Rismatic steel bar of a Square cro ss section (looxlo0)mm is loaoled by Compressive force P= 1300 K, the bar has length 2.5 m, Eg=200GPay V=0.3,determine the shortening 8, the increase in the dimensions of cross Section, the change in Volume DV of the bar? loomm loomm
Question 5 A steel column with a rectangular hollow section is subject to a vertical downward load P1 and a horizontal load P2, as shown in Figure 5 below. If the width of the hollow section is 70mm and the thickness is 5mm, determine the maximum compressive stress at the base of the column. P1=500KN, P2=100kN. P1 - P2 e =110mm Top plate- P2 P1 1m L120mm 120mm (b) Top view showing location of loads (a) Column elevation Figure 5: The cantilever column is fixed at the base.
PROBLEM 01: Hollow bar length is 1.40m long and tube length is three-fourth as long as the bar. Torque T=1100N.m acts at the free end of the bar. Both the bar and tube are made of an aluminum alloy with shear modulus of w ww elasticity G=27GN/m². Given that dl=35mm, d2=45mm, d3=60mm, d4=70mm. Determine the following: a. Maximum shear stress in both the bar and tube b. Angle of twist at the end A of the bar. (In degrees) Tube Fixed plate End plate Tube d3 d1 d2 d4 Bar Cross-section of the bar and tube
A
Determine the normal stress in the steel plate. Gusset plate is 16 mm thick column pin diameter = 20 mm gusset plate steel plate 70 kN pin 60mm 8-mm plate thickness 183.45 MP 0148.53 MPa 58.33 MP3 22282 MP A 14583MP
The aluminum W 310 x 202 (wide flange) column is subjected to an eccentric axial load P as shown. The maximum compressive stress in the column is given by the so-called secant formula: where --- [¹ + ( √5)] ec o 1+ sec max E ō = P/A = average stress A = 25800 mm² = cross-sectional area of the column e = 85 mm = eccentricity of the load c = 170 mm = half depth of the column r = 142 mm = radius of gyration of the cross section L = 7100 mm = length of the column E = 71 x 10⁹ Pa = modulus of elasticity Determine the maximum load P that the column can carry if the maximum stress is not to exceed 120 × 10^6 Pa. Terminate the computation when Σa < 0.0005%.
The beam is subjected to a loading condition as shown in th figure. Determine the (a) maximum tensile stress and (b) maximum compressive stress with the givenm cross section. Show you complete solution and diagram.
For the assembly shown in the figure below, Determine the state of stress at point A on the cross section of the pipe at section a-a. 20 mm P 170N d 30mm Section a-a 120mm b 220mm