The aluminum bar of cross-se ctional are a 0.6 in.2 carries the axial lo ads shown in the fig ure. Compute the total change in length, in inches, of the bar given that E = 10 x 106 psi. 6000 lb 4000 lb 7000 lb 5000 lb e 3 ft 5 ft - to 4 t-

The aluminum bar of cross-se ctional are a 0.6 in.2 carries the axial lo ads shown in the fig ure. Compute the total change in length, in inches, of the bar given that E = 10 x 106 psi. 6000 lb 4000 lb 7000 lb 5000 lb e 3 ft 5 ft - to 4 t-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The figure shows a cutaway view of an assembly in which a solid bronze [G = 6,500 ksi] rod (1) is fitted inside of an aluminum alloy [G = 4,000 ksi] tube (2). The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at A. The rod diameter is d1 = 1.65 in. The outside diameter of the tube is D2 = 2.7 in. and its wall thickness is t2 = 0.130 in. Overall dimensions of the assembly are a = 49 in. and b = 11 in. The allowable shear stresses for the bronze and aluminum materials are 10500 psi and 7800 psi, respectively. Further, the rotation angle of end B must be limited to a magnitude of 5.6°. Based on these constraints, what is the maximum torque TB that can be applied at end B?
Show all units and step by step solution.Formula attached.
The compound bar ABCD has a uniform cross-sectional area of 0.28 in2.Determine the change in length (in inches) of the bar if an axial force P = 3676 lbis applied.The moduli of elasticity are 29037 ksi for steel and 10006 ksifor aluminum. Round off the final answer to four decimal places.
Determine the x-, y-, and z-coordinates of the mass center of the body constructed of three pieces of uniform thin plate which are welded together. 560 mm 240 480 mm mm 85 mm 185 mm 320 mm The tolerance is + 1 in the 3rd significant digit. = i mm i mm i mm
A rigid bar is attached to two vertical rods before a load is applied. Compute the vertical movement under P= 50kN *DRAW THE FBD; COMPLETE SOLUTION *USE 3 DEC PLACES
The cross-sectional area of the bar is 5 cm. Use E = 70 GPa for aluminum, and g= 200 GPa for steel. L. Aluminum Steel Aluminum 80 kN 20 kN -30 kN +70 kN A IB +3 m 4m 5 m What is the elongation in segment AB (Aluminum)? * O -6.8571 x10^-3 m O 6.8571 x10^-3 m O -7.8571 x10^-3 m O 7.8571 x10^-3 m What is the elongation in segment BC (Steel)? * O 2 x10^-3 m O 3x10^-3 m O -3x10-3 m O -2 x10^-3 m What is the elongation in segment CD (Aluminum)? * O 6.8571 x10^-3 m O -2.8571 x10^-3 m O 2.8571 x10^-3 m O -6.8571 x10^-3 m What is the total elongation of the bar? * 6 x10^-3 m O 5 x10^-3 m O 4 x10^-3 m O -6 x10^-3 m
A steel column is supported at the top by two steel rods so as to prevent movement at the top in the x-direction and the y-direction as shown. The column in this case is assumed to be fixed at the bottom and free to rotate but not translate at the top (pin support in x and y directions). If the steel rod along x-x fails (snaps). In this case, the recommended value of Kx for this column should be equal to:
i need the answer quickly
The figure shows a cutaway view of an assembly in which a solid bronze [G = 6,500 ksi] rod (1) is fitted inside of an aluminum alloy [G = 4,000 ksi] tube (2). The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at A. The rod diameter is d1 = 1.65 in. The outside diameter of the tube is D2 = 3.6 in. and its wall thickness is t2 = 0.155 in. Overall dimensions of the assembly are a = 42 in. and b = 12 in. The allowable shear stresses for the bronze and aluminum materials are 9500 psi and 7800 psi, respectively. Further, the rotation angle of end B must be limited to a magnitude of 4.9°. Based on these constraints, what is the maximum torque TB that can be applied at end B?
The force R is the resultant of P and Q. Determine Q and the angle θ
A uniform beam of weight Wis supported by the two rods, the lower ends of which are at the same level just before the beam is supported, as shown in figure. The ratio of the areas Aluminium (E = 70 GPa) 2 m 1.5 m W 3 m 3m Aaluminium Asteel Steel (E = 200 GPa) 0.5 m of the rods so that the beam will be horizontal after it is attached to the rods is
Solid mech.