The beam is subjected to a loading condition as shown in th figure. Determine the (a) maximum tensile stress and (b) maximum compressive stress with the givenm cross section. Show you complete solution and diagram.

The beam is subjected to a loading condition as shown in th figure. Determine the (a) maximum tensile stress and (b) maximum compressive stress with the givenm cross section. Show you complete solution and diagram.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 125 mm. The cross-sectional dimensions of the tee shape are b = 15 mm, d = 23 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 με is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P?
A beam ABC with an overhang from B toC supports a uniform load of 200 lb/ft throughout itslength (see figure). The beam is a channel section withdimensions as shown in the figure. The moment of inertiaabout the z axis (the neutral axis) equals 8.13 in4.(a) Calculate the maximum tensile stress σt andmaximum compressive stress σc due to theuniform load.(b) Find the required span length a that results inthe ratio of larger to smaller compressive stressbeing equal to the ratio of larger to smaller tensilestress for the beam. Assume that the totallength L =a + b = 18 ft remains unchanged.
The section of a thick beam has the dimensions shown in the figure below. Calculate the section properties lz, ly and Izy (Izy = product of inertia) referred to horizontal and vertical axes through the centroid of the section. Refer to Section 6 in your notes for properties of planed sections. Also determine the direct stress at the point A due to a bending moment My = 55 Nm. (Hint: use Page 7-9 in your notes) Ay A 5 mm 20 mm G 5 mm 5 mm 10 mm
A small aluminum alloy [E = 80 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 165 mm. The cross- sectional dimensions of the tee shape are b = 19 mm, d = 29 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 430 µɛ is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P ЗР Strain gage d D E H Answer: P = i
A square beam (w=0.03 m) is loaded with a point load of 1000 N and a moment load of 1000 Nm, as shown. i. Determine maximum deflection of the beam using step by step analytical equations. ii. Determine the Maximum stress in the beam using step by step analytical equations iii. For both top fibers and bottom fibers of the square beam, specify the type of the stresses.
A small aluminum alloy [E= 77 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 160 mm. The cross- sectional dimensions of the tee shape are b= 22 mm, d = 33 mm, and t= 4 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 410 uɛ is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? %3D %3D %3D 3P Strain gage E Answer:
A simple pin-connected truss is loaded and supported as shown. The load Pis 240 kN. All members of the truss are aluminum pipes that have an outside diameter of 130 mm and a wall thickness of 14 mm. Determine the normal stress in each truss member. Assume truss dimensions of a = 10 m, b = 6.25 m, and c= 5 m. Tensile stress is positive, while compressive stress is negative. b D Answer: OAB 11 JAC OBC= OBD = OCD = i M M a B MPa MPa MPa MPa MPa
At a point on the surface of a machine component the stresses acting on the e face of a stress element are or = 55 MPa and Txy = 30 MPa (see figure). T- 30 MPa a, = 55 MPa What is the allowable range of values for the stress oy if the maximum shear stress is limited to TO = 34 MPa? Round to one decimal place. (a) Lower limit is MPa (b) Upper limit is MPa
4.15 Knowing that for the casting shown in the figure the allowable stress is 6 ksi in tension and 15 ksi in compression, determine the maximum couple M that can be applied.
2. (3 points) When loading is applied at a point on a body, the stress distributions at different cross sections are different. However, the stress distribution becomes uniform at locations far from the applied load. This is due to which principle? Name the principle. P Load distorts lines located near load P P C C Lines located away from the load and support remain straight P O avg A section a-a section b-b section c-c -Load distorts lines located near support Your answer
A thin polymer plate PQR is deformed so that corner Q is displaced downward 0.9 mm to new position Q', as shown in. Determine the shear strain at Q' associated with the two edges (PQ and QR). Assume a = 150 mm, b = 216 mm, c = 180 mm, and A = 0.9 mm. a b P R C Answer: Shear strain y = Q i A X urad.
Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Determine the magnitude of the force P (in lb) for which the tensile stress in rod AB is thrice the magnitude of the compressive stress in rod BC if Q = 20.11 lb.