A hollow aluminum tube is rigidly attached between steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in aluminum of 80 MPa, in steel of 150 MPa or bronze of 100 MPa. Steel Aluminum Bronze B A ЗР 2P d = 16 mm d outside = 30 mm d inside = 20 mm d = 60 mm -100mm- -150mm- -125mm-

A hollow aluminum tube is rigidly attached between steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in aluminum of 80 MPa, in steel of 150 MPa or bronze of 100 MPa. Steel Aluminum Bronze B A ЗР 2P d = 16 mm d outside = 30 mm d inside = 20 mm d = 60 mm -100mm- -150mm- -125mm-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A brass (? =5.6 ? 10^6 ???) and aluminum (? = 3.7 ? 10^6 ???) cylinders are bonded together at B, and are attached to fixed supports A and C. Determine (a) The torsion in AB, (b) The torsion in BC, (c) The maximum shearing stress in AB (d) The maximum shearing stress in BC.
A 25-mm-diameter aluminum rod, 4 m long, is subjected to an axial tensile load of 50 kN Assume a proportional limit of 200 MPa and E = 70 GPa. Compute: a) Stress b) Strain c) Total elongation
A steel component is subjected to alternate cyclical loading. The steel follows Basquin's law for high cycle fatigue, o, x N = C, (where the stress amplitude is in MPa). Ignore the geometric detail and assume that Marin's modifying factors are all equal to 1. You are given the minimum stress ain = -213 MPa, the maximum stress omax = 213 MPa. The material data are Tensile strength oUTS = 539 MPa, Basquin's constant c, = 875 MPa, Basquin's exponent a = 0.085. a) Calculate the stress ratio R, the stress amplitude o, in MPa and the mean stress am in MPa. The answers are acceptable with a tolerance of 0.01 for R and of 1 MPa the stresses. R: MPa MPа b) Calculate the corresponding life, in 10° cycles, (tolerance of 0.1 106 cycles) N :
Problem 1 An axial force of P is applied to the center of the rigid end plate shown below. If the portion of the load carried by the aluminum plates is half the portion of the load carried by the brass core, (a) determine the value of h, (b) the total load if the stress in the brass is 50 MPa. Brass core (E = 105 GPa) Aluminum plates (E = 70 GPa) Rigid end plate 300 mm 60 mim 40 mm
Please solve it fast A mild steel specimen having Young’s modulus of 200 GPa and original length of 300 mm is tested for a stress of value 500 MPa. Find the resultant elongation in the specimen.
The solid rod has a diameter of 20mm. Find the following: Angle of twist at C with respect to A (in radians) Angle of twist at B with respect to A (in radians) Maximum shear stress at A (in MPa) (Shear stress at support, at a point 7mm from center. (in MPa) A-36 steel with the following properties: Modulus of Elasticity, E = 29x10^3 ksi or 200 GPa Shear Modulus/Modulus of Rigidity, G = 11.5x10^3 ksi or 79.3 GPa Poisson's Ratio, nu = 0.260 Temperature Coefficient for thermal expansion, a = 6.6x10^-6/°F or 11.7x10^-6/°C
The state of plane stress shown occurs at a critical point of a steel machine component. As a result of several tensile tests, it has been found that the tensile yield strength is o, = 250 MPa for the grade of steel used. Determine the factor of safety with respect to yield using (a) the maximum shearing stress criterion, and (b) the maximum distortion energy criterion. ↑y 40 40 MPa 80 MPa 25 MPa ➜X
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 6) What is the deformation &c in mm? 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
Required information Consider the loading shown. The allowable normal stress for the steel used is 160 MPa. 0.8 m 50 kN/m B -2.4 m- 0.8 m For the selected design, determine the actual value of Om in the beam. (Round the final answer to one decimal place. You must provide an answer before moving to the next part.) The actual value of om in the beam is 160 MPa.
*7-88. Nylon strips are fused to glass plates. When moderately heated the nylon will become soft while the glass stays approximately rigid. Determine the average shear strain in the nylon due to the load P when the assembly deforms as indicated. 2 mm 3 mm 5 mm 3 mm 5 mm 3 mm
1/2 Problem 1: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown in. If the stress must not exceed 14OMPA in either rod, determine the smallest allowable value of the diameter of rod AB and ВС. 300mm B 40 kN 250mm - d2 30 kN