A and b A 2-ft rod with a modulus of elasticity of 8840 ksi, is subjected to a tensile force of1000 lb and has an elongation of 0.009 in. The initial radius of the material is mostnearly?9.80 in2.83 in0.62 inO 0.31 in Two alloy samples (A and B) have the same modulus of elasticity; both experience thesame tensile load from each side.Sample A is cylindrical with a diameter (d).Sample B has a square cross-sectional area with sides (b).Which of the following is the best representation of the samples' (A and B) axialstrains when (b=d)?Strain A< Strain BStrain A= Strain BStrain A> Strain BStrain A= 1.5* Strain B

Answered: Image /qna-images/answer/4b82c99e-a10d-42d9-8eaa-1e3794849ae0.jpg

A 2-ft rod with a modulus of elasticity of 8840 ksi, is subjected to a tensile force of 1000 lb and has an elongation of 0.009 in. The initial radius of the material is most nearly? O 9.80 in 2.83 in 0.62 in 0.31 in

A 2-ft rod with a modulus of elasticity of 8840 ksi, is subjected to a tensile force of 1000 lb and has an elongation of 0.009 in. The initial radius of the material is most nearly? O 9.80 in 2.83 in 0.62 in 0.31 in

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A test conducted on a steel bar whose cross section is 0.5 in. by 4 in. is performed. Anaxial load of P = 30,500 lb. produced a deformation of 0.00103 in. over a gauge lengthof 2 in. and a decrease of 0.000078 in. in the 0.5-in. thickness of the bar. Determinea. Poisson’s ratio,b. the elastic modulusc. the decrease in the 4-in. cross-sectional dimension.
The failure stress of a homogeneous steel bar having a diameter of 10 mm is 250 MPa. Using a factor of safety of 2.0 and if the elastic mođulus and length of the bar is 200 GPa and 2 m respectively, calculate the elongation in mm of the bar corresponding to the maximum load it can support. (А) 5 (в) 2.5 1.25 D) 0.625
q7 A steel bar 2 m long, 20 mm wide and 15 mm thick is subjected to a tensile load of 30 kN. If Poisson's ratio is 0.25 and Young's modulus is 200 GPa, an increase in volume will be (b) 150 mm3 (d) 130 mm3 (a) 160 mm3 (c) 140 mm3
A steel rod with a cross-sectional area of 0.25in2 is stretched between two fixed points. The tensile force in the rod at 70°F is 1200lb. If a = 6.5x10-6/°F and E = 29x106 psi, What will be the stress at 0°F? At what temperature will the stress be zero? A bronze bar 3m long with a cross-sectional area of 320mm2 is placed between two rigid walls. At ta temperature of -20°c, the gap A = 25mm. Find the temperature at which the compressive stress of the bar will be 35 MPa. Use a = 18x10-6 m/ (m. °C) and E = 80GPA.
A bar 500mm long and 200 mm in diameter is elongated by 1.2mm under axial pull of 105kn calculate stress and modulus of elasticity of bar
Vol. Strain.
A steel rod with a cross sectional area of 120 (mm) ^2 is stretched between two fixed points. The tensile load at 20°C is 4200N. What will be the stress at-25°C? a=11.7x [10] ^(-6)/°C and E = 200GPA. See figure 06. * Figure 06 120 MPa 130 MPa 140 MPa 150 MPa
A steel bar, whose cross section is 0.60 inch by 4.10 inches, was tested in tension. An axial load of P = 31,025 lb. produced a deformation of 0.115 inch over a gauge length of 2.10 inches and a decrease of 0.0080 inch in the 0.60-inch thickness of the bar. a. Determine the lateral strain. b. Determine the axial strain. c. Determine the Poisson’s ratio v. d. Determine the decrease in the 4.05-in. cross-sectional dimension (in inches).
A mild steel bar of square cross-section 40 mm x 40 mm is 400 mm long it is subjected to a longitudinal tensile stress of 440 N/mm² and lateral compressive stress is 200 N/mm² in perpendicular directions. E = 2 x 105 N/mm², μ = 0.3. What is the approximate elongation of the bar in the longitudinal direction?
An applied torque results in a shear strain (y) of 3.75 x 103 in a solid circular steel shaft. At this strain, a portion of the shaft cross- section yields as shown in Figure 2. Determine the magnitude of the applied torque. Take G = 80 GPa and yy = 2.8125 x %3D 10-3 FIGURE 2: Plastic zone 50 mm 200 mm Elastic core
GIVEN: Bar has a cross-sectional area of 4 in? and is placed between two rigid immoveable supports when it is 30.00 inches long at a temperature of -20°F. REQ’D: A) The stress in the bar at 90°F if it were made of steel. Esteel = 10 x 10° psi asteel = 13 x 106/°F B) The final length of the aluminum bar
please show your sholutions. thank you!