The tension of a specimen of steel having an initial diameter of 0.507 in. was tested using a gauge length of 2 in. The following data were obtained for the elastic and plastic states. For the elastic state PAlb) 10 1000 2000 3000 4000 7000 8400 8800 9200 For the plastic state PAlb) 8800 9200 9100 13200 15200 17000 16400 14800 A/(in) 10 The reduction in the area Ris 0.0004 0.0006 0.0010 0.0013 0.0023 0.0028 0.0036 0.0089 NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. % A, (in2) 0.1984 0.1978 0.1963 0.1924 0.1875 0.1563 0.1307 0.1077 What are the values of the yield strength, Sy and the reduction in the area? The value of the yield strength Sy is [ kpsl. 4

The tension of a specimen of steel having an initial diameter of 0.507 in. was tested using a gauge length of 2 in. The following data were obtained for the elastic and plastic states. For the elastic state PAlb) 10 1000 2000 3000 4000 7000 8400 8800 9200 For the plastic state PAlb) 8800 9200 9100 13200 15200 17000 16400 14800 A/(in) 10 The reduction in the area Ris 0.0004 0.0006 0.0010 0.0013 0.0023 0.0028 0.0036 0.0089 NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. % A, (in2) 0.1984 0.1978 0.1963 0.1924 0.1875 0.1563 0.1307 0.1077 What are the values of the yield strength, Sy and the reduction in the area? The value of the yield strength Sy is [ kpsl. 4

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If the posson ratio of elastic material is 0.453 the ratio of modulus of rigidity to Young modulus
Q.1 The yield stresses (oy) have been measured using steel and aluminum specimens of various grain sizes, as follows: Material D (µm) σΥ (MPa) Steel 60.5 160 136 128 Aluminum 11.1 235 100 223 (a) Determine the coefficients o and kỵ in the Hall- Petch for these two materials. (b) Determine the yield stress in each material for a grain size of d=26 um.
A steel bar is held by two fixed supports as shown in the figure and is subjected to an increased temperature of AT = 200°C. If coefficient of thermal expansion and young's modulus of elasticity of steel are 11 x 10-6/°C and 200 GPa respectively, the magnitude of thermal stress (in MPa) induced in the bar is
The rigid horizontal bar ABC of negligible mass is connected to two rods as shown in the figure. If the system is initially stress-free, calculate the temperature change that will cause a tensile stress of 90 MPa in the brass rod. Assume that both rods are subjected to the same change in temperature.
A round steel alloy bar with a diameter of 19mm and a gauge length of 76mm was subjected to tension, with the results shown in Table. Using a computer spreadsheet program, plot the stress–strain relationship. From the graph, determine the Young’s modulus of the steel alloy and the deformation corresponding to a 37kN load.
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 40 x 103 mm while those at CD decrease 80 x 10 ³ mm in the 230-mm-gage length. Using E = 150 GPa, determine the flexural stress at the bottom fiber. Answer must be in MPa. Given: a = 40 mm, b 130 mm, and c = 90 mm. gage length a mm b mml c mm
Answer in two decimal places please
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 50 x 10 mm while -3 those at CD decrease 60 x 10 nm in the 210 mm gage length Using E 140 GPa, determine the flexural stress at the top fiber. Answer must be in MPa. Given: a 50 mm, b 130 mm, and c 80 mm. gage length la mm omm c mni
Answer in two decimal places please
A 4-m-long steel plate with a rectangular cross section (10 mm * 50 mm) is resting on a frictionless surface under the sun. The plate temperature is meas-ured to be at 40°C. The plate is then moved into a cold room and is left to rest on a frictionless surface. After several hours, the plate temperature is meas-ured to be at 5°C. The steel has a modulus of elasticity equal to 200 GPa and a coefficient of thermal expansion equal to 1.1 * 10-5m/m/°C. a. What is the length of shrinkage?b. What tension load is needed to return the length to the original value of 4meters?c. What is the longitudinal strain under this load?
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 20 x 103 mm while those at CD decrease 60 x 103 mm in the 230- mm-gage length. Using E = 180 GPa, determine the flexural stress at the top fiber. Answer must be in MPa. Given: a = 40 mm, b = 130 mm, and c= 70 mm. gage length a mm A B. b mm c mm