Strain =600Stress =Strain =500Stress =4005003004003002002001001000.0000.0020.0040.006Strain0.000.040.080.120.160.20StrainStress (MPa) A bar of a steel alloy that exhibits the stress-strain behavior shown in the Animated Figure 6.22 is subjected to a tensile load;the specimen is 375 mm (14.8 in.) long and has a square cross section 5.5 mm (0.22 in.) on a side.(a) Compute the magnitude of the load necessary to produce an elongation of 0.375 mm (0.015 in.).iN(b) What will be the deformation after the load has been released?imm

Answered: Image /qna-images/answer/1000c804-fc17-44f2-b4cd-4a8df94623fe.jpg

A bar of a steel alloy that exhibits the stress-strain behavior shown in the Animated Figure 6.22 is subjected to a tens the specimen is 375 mm (14.8 in.) long and has a square cross section 5.5 mm (0.22 in.) on a side. (a) Compute the magnitude of the load necessary to produce an elongation of 0.375 mm (0.015 in.). i N (b) What will be the deformation after the load has been released?

A bar of a steel alloy that exhibits the stress-strain behavior shown in the Animated Figure 6.22 is subjected to a tens the specimen is 375 mm (14.8 in.) long and has a square cross section 5.5 mm (0.22 in.) on a side. (a) Compute the magnitude of the load necessary to produce an elongation of 0.375 mm (0.015 in.). i N (b) What will be the deformation after the load has been released?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure below. Axial loads are applied at the positions indicated. Find the maximum value of P (Newton) that will not exceed a stress in steel of 147 mPa. in aluminum of 94 mPa, or in bronze of 109 mPa. The final answer should have 2 decimal places where cross-sectional area of Steel = 513 mm2; Aluminum = 416 mm2; Bronze = 207 mm2 Length of Steel = 3.0 m; Aluminum = 2.7 m; Bronze = 1.8 m
Stress analysis
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 880 mm. The cross-sectional dimensions of the beam are b1 = 37 mm, d1 = 86 mm, b2 = 22 mm, d2 = 22 mm, and a = 7.5 mm. For this material, the allowable tensile bending stress is 11 MPa, and the allowable compressive bending stress is 9 MPa. Determine the largest moment M that can be applied as shown to the beam.
An extruded polymer beam is subļected to a bending moment M. The length of the beam is L = 860 mm. The cross-sectional dimensions of the beam are bq = 36 mm, d = 89 mm, b2 = 22 mm, d2 = 22 mm, and a = 7 mm. For this material, the allowable tensile bending stress is 10 MPa, and the allowable compressive bending stress is 10 MPa. Determine the largest moment M that can be applied as shown to the beam. b2 ja a M d2 d1 A B b1 Answer: 410.8451 N-m
30. An aluminum alloy rod has a circular cross section with a diameter of 8mm. The rod is subjected to a tensile load of 5kN. Assume that the material is in the elastic region and E = 69 GPa. If Poisson's Ratio is 0.33, what will be the lateral strain? E= 6/8 v = -E(lateral)/(axial)
An aluminum alloy rod has a circular cross section with a diameter of 7mm. The rod is subjected to a tensile load of 5kN. Assume that the material is in the elastic region and E = 69 GPa. If Poisson's Ratio is 0.38, what will be the lateral strain? E=6/8 v= -€(lateral)/e(axial) V ominorbooomes
Quick
A 5-mm-thick rectangular alloy bar is subjected to ajtensile load P by pins at A and B, as shown in the figure. The width of the bar is w = 33 mm. Strain gages bonded to the specimen measure the following strains in the longitudinal (x) and transverse (y) directions: €, =710 με and ε,--255 με (a) Determine Poisson's ratio for this specimen. (b) If the measured strains were produced by an axial load of P = 24 kN, what is the modulus of elasticity for this specimen? Answers: (a) v= (b) E= GPa
2.58 Knowing that a 0.02-in. gap exists when the temperature is 75°F, determine (a) the temperature at which the normal stress in the aluminum bar will be equal to -11 ksi, (b) the corresponding exact length of the aluminum bar. 0.02 in. -14 in. 18 in. Aluminum A = 2.8 in² Bronze A = 2.4 in² E = 15 × 10º psi a = 12 x 10-6/°F E = 10.6 × 106 psi α = 12.9 x 10-6/°F Fig. P2.58 and P2.59
The elastic portion of the tension stress-strain diagram for an aluminum alloy is shown in the figure. The specimen used for the test has a gauge length of 2 in. and a diameter of 0.5 in. If the applied load is 10 kip, determine the new diameter of the specimen. The shear modulus is G al =3.811032 ksi
A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure. Axial loads are applied at the positions indicated. If P 4000 Ib and the cross-sectional area of the rod is 1.0 sq.in. What is %3D the stress in the bronze? (in ksi) Note: indicate sign (no sign means positive/tenslon) 4P Steel Bronze Aluminum 2 ft 3 ft 2.5 ft
2. A steel bar, whose cross section is 0.55 inch by 4.05 inches, was tested in tension. An axial load of P = 30,500 lb. produced a deformation of 0.105 inch over a gauge length of 2.05 inches and a decrease of 0.0075 inch in the 0.55-inch thickness of the bar. Determine the lateral strain. * Your answer Determine the axial strain. Your answer Determine the Poisson's ratio v. * Your answer Determine the decrease in the 4.05-in. cross-sectional dimension (in inches). * Your answer