The mean dimensions of the cross section of the leading edge and torsion box of an airplane wing can be approximated as shown. The wing is subjected to a torque of 4.7 MN m and the wall thickness is 10 mm. The wing is made of 2014-T6 aluminum alloy. Figure 1 of 1 0.5 m 10 mm 10 mm 10 mm- 2 m 0.25 m 0.25 m Express your answer with the appropriate units. Tavg 124 MPa Part B Submit Correct My Answers Give Up Determine the angle of twist per meter length of the wing. Express your answer with the appropriate units. VΠΙ ΑΣΦ It vec Submit My Answers Give Up Incorrect; Try Again; 5 attempts remaining ? °/m

The mean dimensions of the cross section of the leading edge and torsion box of an airplane wing can be approximated as shown. The wing is subjected to a torque of 4.7 MN m and the wall thickness is 10 mm. The wing is made of 2014-T6 aluminum alloy. Figure 1 of 1 0.5 m 10 mm 10 mm 10 mm- 2 m 0.25 m 0.25 m Express your answer with the appropriate units. Tavg 124 MPa Part B Submit Correct My Answers Give Up Determine the angle of twist per meter length of the wing. Express your answer with the appropriate units. VΠΙ ΑΣΦ It vec Submit My Answers Give Up Incorrect; Try Again; 5 attempts remaining ? °/m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SOLVE 5 DECIMAL
Calculate the amount of force needed to break a sample of mullite in 3-point bending with the following geometry (dimensions are in mm). 100 5 Flexural Strength Modulus of Elasticity Material MPa ksi GPa 10º psi Mullite (3Al2O3-2SiO2) 185 27 145 21 7.5
Properties: Rod 1 8F D = 40 mm d = 20 mm L = 1.3 meter E = 80 Gpa ROD 1 ROD 2 Rod 2 D = 80 mm d = 20 mm L = 1.0 meters E = 80 Gpa 3F 2. The composite rod shown in the figure is composed of three rods rigidly welded together. Applied forces in terms of "F" are exerted in different parts of the composite rod. Compute the maximum safest value of "F" if the allowable total deformation of the composite rod is limited to 0.50 mm only. ROD 3 2F Rod 3 D = 60 mm d = 20 mm L = 1.2 meters E = 80 GPa 7F
An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Find the maximum value of P in kN that will not exceed a stress in steel of 140 MPa, in aluminum of 90 MPa, or in bronze of 100 MPa
A hollow aluminum driveshaft has the dimensions shown and is subjected to the torques shown. If the failure shear strength of the aluminum is 25 ksi, what is the factor of safety for the driveshaft? Give a number with three significant figures for your answer. 326 ft-lb outside dia = 2 in inside dia = 1.5 in 326 ft-lb outside dia = 2 in inside dia = 1.5 in %3D cross-section 6.5 ft
In any case ,The final answer must be correct. Please include the Diagram
A prismatic aluminum bar has cross-sectional dimensions 40 x 60 mm and a length of 350 mm. The modulus of elasticity is 70 GPa and Poisson's ratio is u=0.35. When an axial load of 100 kN is applied, the proportional change in the bar's volume is
Determine the maximum tensile strength of the steel bar described by the following data Initial diameter = 12 mm Final diameter = 6.5 mm Initial length = 60 cm Final length = 86 cm Ultimate load = 5000 kgf
My student number is 202010237
4.20 A cylindrical aluminum alloy rod with a 0.5 in. diameter is subjected to ten- sion. Determine the magnitude of the load required to produce a 10 in. change in diameter if the deformation is entirely elastic. Assume a Young's modulus of 11 X 106 psi and a Poisson's ratio of 0.33.
I need to solve the question of strength materials
4