A bar obtained by bonding together pieces of aluminum (Ea = 70 GPa) and brass (E = 105 GPa) has the cross section shown below. Considering that the allowable stress (both in compression and tension) of aluminum and brass are 120 MPa and 180 MPa, respectively, determine the largest moment M that can be applied about the horizontal axis.

A bar obtained by bonding together pieces of aluminum (Ea = 70 GPa) and brass (E = 105 GPa) has the cross section shown below. Considering that the allowable stress (both in compression and tension) of aluminum and brass are 120 MPa and 180 MPa, respectively, determine the largest moment M that can be applied about the horizontal axis.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

GIVEN: Bar has a cross-sectional area of 4 in? and is placed between two rigid immoveable supports when it is 30.00 inches long at a temperature of -20°F. REQ’D: A) The stress in the bar at 90°F if it were made of steel. Esteel = 10 x 10° psi asteel = 13 x 106/°F B) The final length of the aluminum bar
The following shaft is composed of two materials, both rigidly bonded. The data is provided in the table: Determine: The maximum torque that can be applied based on the maximum stresses of each material. The total deformation of the shaft with the torque from the previous section. The maximum torque that can be applied if the maximum deformation of the shaft is 2.50 rad.
In the figure shown below, determine: 1) The final temperature if the normal stress at aluminium is oal = -90 MPa and the initial temperature 20°C. 2) The final length of the aluminium member. Aluminum A=1800mm? E=73GPA Bronze A=1500mm2 E=105GPA a=23.2x10-6/°C a=21.6x10-6/°C Gap=0.5mm 0.35m 0.45m
The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar (1) is a bronze alloy [E = 94 GPa] with a cross-sectional area of A₁ = 280 mm2. Bar (2) is an aluminum alloy [E = 71 GPa] with a cross-sectional area of A2 = 590 mm². All bars are unstressed before the load P is applied; however, there is a 3-mm clearance in the pin connection at A. Assume L₁ = 1840 mm, a = 880 mm, b = 540 mm, c = 430 mm, and L₂ = 1340 mm. If a load of P = 87 kN is applied at B, determine (a) the normal stresses in both bars (1) and (2). (b) the downward deflection of point A on the rigid bar. h (1) L₁ b a BI Answers: C (2) D L2
3) An bronze rod is rigidly attached between a aluminum rod and a steel rod as shown. Axial loads are applied at the positions indicated. Find the maximum allowable value of P that will not exceed a stress in steel of 140MPA, in aluminum of 90MPA or in bronze of 100MPа. Aluminum A = 500mm? Bronze A = 200mm? Steel A = 150mm2 2P ЗР L st = 1.2m L br = 2m Lal = 3.5m
A rigid bar of negligible weight is supported and loaded with 70 kN, compute the temperature change AT (°C) that will cause the stress in the bronze rod (L = 1.5 m, A = 300 mm?, and E = 83 GPa) to be 50 MPa. Assume a = 18.9 µm/(m°C) for bronze and 12.8 um/(m°C) for aluminum (L = 3 m, A = 750 mm2, and E = 70 GPa). Aluminum Bronze 2.5 m 1.5 m 70 kN
Problem 1 An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Aluminum Steel A=800mm2 A=1000mm2 Bronze A=700mm? 4P 2P 500mm 600mm 700mm 1. What is the maximum value of P that will not exceed the axial stress bronze of 105 MPa? 2. What is the maximum value of P that will not exceed the axial stress in aluminum of 90 MPa? 3. If P=10KN, what is the axial force to be carried by the aluminum in KN? 4. If P is 5KN, what is the axial stress of steel?
One of the following values is a possible for possion ratio for steel ? a. Zero b. one c. 0.3 d 0.9
I need the answer as soon as possible
2. Given a 5 mm diameter steel wire, which is 4 meters long, carries an axial tensile load P. Find the maximum safe value of P if the deformation of the wire is limited to 5.5 mm and the allowable normal stress of the wire is 280 MPa. Use 200 000 MPa for the modulus of elasticity of steel.
A tapered steel bar of length 2m is subjected to an axial load of 20kN. Take modulus of steel as 200GPa. What is the strain produced in the bar? (in 10-5) = 100 mm 2m >= 50 mm 20000 N
5. The rigid bar of negligible weight is pinned at O and attached to two vertical rods. Assuming that the rods were initially stress-free, what is the largest load P that can be applied without exceeding stresses of 150 MPa in the steel rod and 70 MPa in the bronze rod? -2 m- -1.5 m- 1.5 m- Bronze A = 300 mm2 E = 83 GPa L=2 m Steel A = 900 mm2 E = 200 GPa L = 1.5 m