In order to address ACL injuries and develop a replacement for ligament injury, a rectangular block of poly-caprolactone (PCL), a = 3 cm wide and b = 2.5 cm deep, is subjected to an axial tensile load (F) as shown in the figure. Measurements show the block to increase in length by Ax = 4.33 x 10$ m (initial length L 25 cm) and to decrease in width by Az 0.125 10$ m, when F is 1 kN. for the Calculate the modulus of elasticity (E) material. Assume ɛy = 6. Show all your work and select the best choice from below. and Poisson's ratio Modulus of Elasticity: A. Cannot be determined B. 4.3 GPa C. 77 GPa D. 7.7 GPa F Poisson's ratio: A. 0.31 В. 0.5 С. 1 D. 0.24

In order to address ACL injuries and develop a replacement for ligament injury, a rectangular block of poly-caprolactone (PCL), a = 3 cm wide and b = 2.5 cm deep, is subjected to an axial tensile load (F) as shown in the figure. Measurements show the block to increase in length by Ax = 4.33 x 10$ m (initial length L 25 cm) and to decrease in width by Az 0.125 10$ m, when F is 1 kN. for the Calculate the modulus of elasticity (E) material. Assume ɛy = 6. Show all your work and select the best choice from below. and Poisson's ratio Modulus of Elasticity: A. Cannot be determined B. 4.3 GPa C. 77 GPa D. 7.7 GPa F Poisson's ratio: A. 0.31 В. 0.5 С. 1 D. 0.24

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A tensile load of 150 kN is applied to a round metal bar with a diameter of 16 mm and a gage length of 80 mm. Under this load the bar elastically deforms so that the gage length increases to 80.1192 mm and the diameter decreases to 15.89 mm. Determine the modulus of elasticity (in MPa) and Poisson's ratio for this metal.
In a tension test, a 105 N.cm work is done to break a 30 cm long glass rod with a 4 mm x 75 mm cross-section area. Modulus of elasticity of glass is 7x10° N/cm?. (Assume linear elastic behaviour of glass until rupture) a) Determine the tensile strength of glass. b) Calculate the length of the glass rod at rupture.
The stress-strain diagram for a metal alloy having an original diameter of 16 mm and a gauge length of 300 mm is given in the figure. Determine approximately the modulus of elasticity for the material, the load on the specimen that causes yielding, and the ultimate load the specimen will support. a (MPa) 700 600 500 400 300 200 100 € (mm/mm) 0 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.001 0.002 0.003 0,004 0,005 0.006 0,007
Minimum of 3 decimal places in all computations.
The information in the photo attached shows elastic properties of a human tibula bone. If you were to take a small cuboidal cross section of the tibula bone and apply the ultimate shear stress, what would be the resulting strain? (a) 1.0 % (b) 6.7 % (c) 10 % (d) 15 % (e) None of the above.
A round steel alloy bar with a diameter of 19mm and a gauge length of 76mm was subjected to tension, with the results shown in Table. Using a computer spreadsheet program, plot the stress–strain relationship. From the graph, determine the Young’s modulus of the steel alloy and the deformation corresponding to a 37kN load.
A brass alloy rod having a cross sectional area of 100 mm2 and a modulus of110 GPa is subjected to a tensile load. Plastic deformation was observed tobegin at a load of 39872 N.a. Determine the maximum stress that can be applied without plasticdeformation.b. If the maximum length to which a specimen may be stretched withoutcausing plastic deformation is 67.21 mm, what is the original specimenlength?
The mean dimensions of the cross section of the leading edge and torsion box of an airplane wing can be approximated as shown. The wing is subjected to a torque of 4.7 MN m and the wall thickness is 10 mm. The wing is made of 2014-T6 aluminum alloy. Figure 1 of 1 0.5 m 10 mm 10 mm 10 mm 2 m 0.25 m 0.25 m Express your answer with the appropriate units. Tavg 124 MPa Submit Correct Part B My Answers Give Up Determine the angle of twist per meter length of the wing. Express your answer with the appropriate units. VΠΙ ΑΣΦ It vec Submit My Answers Give Up Incorrect; Try Again; 5 attempts remaining ? °/m
A brass alloy rod having a cross sectional area of 0.24 in.2and a modulus of 16 * 106 psi is subjected to a tensile load. Plastic deformation was observed to begin at a load of 8,944 lb.a. Determine the maximum stress that can be applied without plastic deformation.b. If the maximum length to which a specimen may be stretched without causing plastic deformation is 3.28 in., what is the original specimen length?
Consider a rectangular specimen of aluminium has a dimension of 10 ?? × 12.7 ?? is pulled in tension with 35500 N. Calculate the resulting strain. Given the modulus of elasticity is 69 × 103??? and assume that the deformation is elastic.
A tensile load of 190 kN is applied to a round metal bar with a diameter of 16 mm and a gage length of 50 mm. Under this load the bar elastically deforms so that the gage length increases to 50.1349 mm and the diameter decreases to 15.99 mm. Determine the modulus of elasticity and Poisson