HMW-1 Regenerative steam power plant shown in figure below employs two feed heaters which are optimally placed such that cycle has the maximum thermal efficiency. The mass of steam generated is 16 kg/s. The feed water leaves each heater as saturated liquid at corresponding bleed pressure. Neglect the pumps work and find: a. Cycle thermal efficiency. b. Specific steam consumption. c. Mechanical efficiency of the turbine-generator gearing unit. Draw the equivalent (T-s) diagram considering an ideal cycle. 70 bar 450°C Gearing unit Generator 15 MW Turbine Super heater Boiler Condenser 0.07 bar Open heater Closed heater Pump Pump Throttling Valve

HMW-1 Regenerative steam power plant shown in figure below employs two feed heaters which are optimally placed such that cycle has the maximum thermal efficiency. The mass of steam generated is 16 kg/s. The feed water leaves each heater as saturated liquid at corresponding bleed pressure. Neglect the pumps work and find: a. Cycle thermal efficiency. b. Specific steam consumption. c. Mechanical efficiency of the turbine-generator gearing unit. Draw the equivalent (T-s) diagram considering an ideal cycle. 70 bar 450°C Gearing unit Generator 15 MW Turbine Super heater Boiler Condenser 0.07 bar Open heater Closed heater Pump Pump Throttling Valve

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Ssoollv
The piping of the circuit in Figure is modified as follows. First, the pipeline from the upper discharge port of the directional control valve is connected to the rod end of the cylinder. Then the pipeline from the lower discharge port of the directional control valve is connected to the blank end of the cylinder. What effect does this have on the minimum flow capacity of the return line filter?
a constant pressure container (inside the piston-cylinder) with 250 kPa pressureat the beginning the mass of the saturated water vapor was 8 kg. Then the saturated steam in the cylinder compressed to 3/4 of its mass vy cooling.1) what's the amount of heat transferred to the environment.
1. A Rankine cycle with reheating has a throttle pressure of 135 bars at the turbine inlet and 28 bars reheat pressure, the throttle and reheat temperature of the steam is 550C, condenser pressure is 0.035 bar, mass flow rate of steam is 10 kg/sec. Draw the T-s and schematic diagram of the cycle and determine the following: (c) theoretical thermal efficiency (d) the steam rate (e) heat rate of the cycle
Derive E(t), F(t), tm, and σ2 for a turbulent flow reactor with 1/7 the power law, i.e.,
One single phase energy meter operating on 230 V and 5 A for 5 hours makes 1940 revolutions. Meter constant in revolution is 400. The power factor of the load will be:
Consider a pump–turbine that operates both as a pump and as a turbine. Under conditions in which the rotational speed ? and the volume flow rate V. are the same for the pump and the turbine, verify that turbine specific speed and pump specific speed are related as
Steam at a pressure of 0.08 bar and a quality of 99.0% enters a shell-and-tube heat exchanger where it condenses on the outside of tubes through which cooling water flows, exiting as saturated liquid at 0.08 bar. The mass flow rate of the condensing steam is 5.8 x 105 kg/h. Cooling water enters the tubes at 15°C and exits at 35°C with negligible change in pressure. Neglecting stray heat transfer and ignoring kinetic and potential energy effects, determine the mass flow rate of the cooling water, in kg/h, for steady-state operation. mwater = i 568765.92 kg/h
An insulated piston-cylinder device contains 4 L of saturated liquid water at a constant pressure of 200 kPa. Water is stirred by a paddle wheel while a current of 8A flows for 50 min through a resistor placed in the water. If one-half of the liquid is evaporated during this constant-pressure process and the paddle-wheel work amounts to 300 kJ, determine the voltage of the source. Also, show the process on a P-v diagram with respect to the saturation lines.
dbb