2-64 Nitrogen enters a steady-flow heat exchanger at 150 kPa, 10°C, and 100 m/s, and it receives heat in the amount of 120 kJ/kg as it flows through it. Nitrogen leaves the heat exchanger at 100 kPa with a velocity of 200 m/s. Determine the Mach number of the nitrogen at the inlet and the exit of the heat exchanger.

2-64 Nitrogen enters a steady-flow heat exchanger at 150 kPa, 10°C, and 100 m/s, and it receives heat in the amount of 120 kJ/kg as it flows through it. Nitrogen leaves the heat exchanger at 100 kPa with a velocity of 200 m/s. Determine the Mach number of the nitrogen at the inlet and the exit of the heat exchanger.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Calculate the flux of water through MF and UF membranes operating at 1 bar pressure and 298 K.…

Q: Convert the concentration of SO2 from 80 pg m temperature of 25°C and a pressure of 101.325 kPa. to…

A: ppm = Conversions are needed to calculate the volume of So2 in cubic meters.

Q: You are designing a heatsink to cool a 100mm tall, 100mm wide surface. The fins you use are…

A: Solution; Given that; Height (H) =100 mm = 0.100 m Width (W) =100 mm=0.100 m Thickness of fins tf=2…

Q: Dinitrogen tetraoxide (N204) decomposes into nitrogen dioxide according to the following balanced…

A: To solve the given problem, we need to follow these steps Part (a): Calculate the equilibrium…

Q: Lubricating oil at 20°C with a density of 871 kg/m³ and a kinematic viscosity of 1.5 x 105 m²/s…

A: Density of the oil = 871 kg/m3 Kinematic velocity (ν) = 1.5×10-5 Inner radius (Ri) = 0.04 m Outer…

Q: A treatment plant has been designed to achieve 99 percent inactivation of Giardia Lamblia using…

A: 99% disinfection Present temperature = 20oCNew temperature = 0.5oC

Q: 1. Consider a reactor operating at 50% power with Tave = 572°F. Assume the following: 1. A fuel…

Q: Q1: A conventional ASP is to be used for treatment of 10,000 m³/d of municipal wastewater. The…

Q: A 1.5-ft³rigid tank contains saturated refrigerant-134 at 170 psia. Initially, 20 percent of the…

Q: When you touch a hot object with your finger, the heat transferred to your finger is by Group of…

A: When two bodies are direct in contact with each other then heat is always transferred from the body…

Q: A heat engine with 0.305 mol of a monatomic gas undergoes the cyclic procedure shown in the pV…

A: Using the given data, we can calculate the temperature at stage 1 (T1) and stage 3 (T3), and then…

Q: An ice cube of 0.05 kg at an initial temperature of -15 c, is placed in 0.6 kg of water at 45 c in…

Q: Help me solve both for my homework. Thank you!

Q: Hydrogen is allowed to diffuse through a palladium plate that is 0.008m thick at 500°C. The…

A: The concentration gradient (dC/dx) across the plate can be approximated by, dxdC=ΔxC2−C1…

Concept explainers

Thermal Processes

Some of the key areas where thermal processes find their application are:

Question

2-64 Nitrogen enters a steady-flow heat exchanger at
150 kPa, 10°C, and 100 m/s, and it receives heat in the
amount of 120 kJ/kg as it flows through it. Nitrogen leaves
the heat exchanger at 100 kPa with a velocity of 200 m/s.
Determine the Mach number of the nitrogen at the inlet and
the exit of the heat exchanger.

Expert Solution

Step 1

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Environmental Engineering: Water Treatment Please consider each of the following points: a. Determine the required residence time for each reactor of 3 equal volume CSTRs in series given a zero-order reaction with a reaction rate constant, k = -5 mg/L hr. The influent concentration is 125 mg/L and 95% conversion is required across the three-reactor system. What is the total reactor system residence time? b. Determine the required residence time for a single CSTR given the same conditions. c. Determine the required residence time for a PFR given the same conditions. d. Why are all three residence time the same?
A power plant in rough terrain has a 100-m stack with an inside radius of 1 m. The plant emits 300 g/s of SO2 from the stack with an exit velocity of 10 m/s at a temperature of 120oC. Ambient temperature is 6oC and the temperature increases at a rate of 2 K/km. At 10 m above ground, surface windspeed is 1.5 m/s on a mostly cloudy night. Find the concentration (mg/m3) of SO2: Directly downwind at a distance of 2 km. At a point located 2 km downwind and 0.1 km off the downwind axis. At the point downwind where it is a maximum. Approximately how far from the stack does this occur?
A spring-loaded piston-cylinder device contains 1.5 kg of carbon dioxide. This system is heated from 200 kPa and 25 °C to 1200 kPa and 300°C. Determine the total heat transfer to and work produced by this system.
Question 3.3 When the air with a pressure of 0.1 MPa and a specific volume of 0.8 m³/kg was provided into a compressor at a flow rate of 0.25 kg/s, its pressure became 0.7 MPa and its specific volume became 0.2 m³/kg. Through the compression, the specific internal energy was increased by 80 kJ/kg, and there was heat loss of 50 kJ/s to the environment. In this case, calculate the work [k]/s = kW] that the compressor did in unit time. Potential energy and kinetic energy can be negligible.
At critical depth O The discharge is maximum for a given specific energy. O The specific energy is maximum for a maximum discharge. O The specific energy is minimum for a maximum discharge. O The discharge is minimum for a given specific energy.
Steam at a pressure of 0.08 bar and a quality of 99.0% enters a shell-and-tube heat exchanger where it condenses on the outside of tubes through which cooling water flows, exiting as saturated liquid at 0.08 bar. The mass flow rate of the condensing steam is 5.8 x 105 kg/h. Cooling water enters the tubes at 15°C and exits at 35°C with negligible change in pressure. Neglecting stray heat transfer and ignoring kinetic and potential energy effects, determine the mass flow rate of the cooling water, in kg/h, for steady-state operation. mwater = i 568765.92 kg/h