An insulated piston-cylinder device contains 4 L of saturated liquid water at a constant pressure of 200 kPa.Water is stirred by a paddle wheel while a current of 8A flows for 50 min through a resistor placed in thewater. If one-half of the liquid is evaporated during this constant-pressure process and the paddle-wheelwork amounts to 300 kJ, determine the voltage of the source. Also, show the process on a P-v diagram withrespect to the saturation lines.

Answer Explanation:Step 1: Step 2: Step 3: Step 4:

Answered: An insulated piston-cylinder device…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the pressure in the pipe (Point A). The area of the reservoir is 100 times the area of the tube of the manometer. 40 cm 20 cm Hg (rd - 13.6)
2. The jet passes through a point A, as shown. Calculate the flow rate. Assume the flow is frictionless and incompressible. 75 mm d 150 mm d- 30- -- 30 m 15 m
In a pump test the suction pressure at the pump inlet is -28.00 kPa below atmospheric pressure. The discharge pressure at a point 960 mm above the inlet is 525 kPa. Hydraulic steel tubing is used for both the suction (inlet) and discharge (outlet) lines with 80 mm OD × 2.8 mm wall. Required If the volume flow rate of water is 88 L/min, calculate the power delivered by the pump to the water in kW, to the nearest 1000th. Discharge pipe Suction pipe Flow Pump |||+
shows a pump employed for lifting water from a sump. If its required to pump 60 liters/sec of water through a 0.1 m diameter pipe from the sump to point 10m above, determine the power required. Also determine pressure intensities at L and M. Assume efficiency of 70%. Pu-(YGYLD)
A well-insulated turbine operating at steady state is shown on the right. Steam enters at 3 MPa, 400°C, with a volumetric flow rate of 85 m³/min. Some steam is extracted from the turbine at a pressure of 0.5 MPa and a temperature of 180°C. The rest expands to a pressure of 6 kPa and a quality of 90%. The total power developed by the turbine is 11,400 kW. Kinetic and potential energy effects can be neglected. Determine (a) the mass flow rate (in kg/s) at each exit, and (b) the diameter of the duct, d₂ (in cm) where steam is extracted P₁ = 3MPa T₁=400°C (AV)₁ = 85 m³/min Turbine P2 = 0.5 MPa T₂ = 180°C V₂= 20 m/s Power out ¹3 P3= 6 kPa x3 = 90%
A galvanized-iron pipe (ε = 0.0005 ft) is to carry air at standard temperature and pressure at a rate of 2.0 ft3/s. The pressure drop is to be no more than 0.50 psi per 100 ft. Design the pipe diameter.
Steam at a pressure of 0.08 bar and a quality of 99.0% enters a shell-and-tube heat exchanger where it condenses on the outside of tubes through which cooling water flows, exiting as saturated liquid at 0.08 bar. The mass flow rate of the condensing steam is 5.8 x 105 kg/h. Cooling water enters the tubes at 15°C and exits at 35°C with negligible change in pressure. Neglecting stray heat transfer and ignoring kinetic and potential energy effects, determine the mass flow rate of the cooling water, in kg/h, for steady-state operation. mwater = i 568765.92 kg/h
Hand written plzzzzz asap..i'll give you more votes if you solve 30-40 mins...
A resonant circuit using a 286-nF capacitor is to resonate at 18.0 kHz. The air-core inductor is to be a solenoid with closely packed coils made from 12.0 m of insulated wire 1.1 mm in diameter. The permeability of free space is 4 x 107 T-m/A K ▼ Part A How many loops will the inductor contain? Express your answer as an integer. G| ΑΣΦ N = 14530 Submit Previous Answers Request Answer ? X Incorrect; Try Again; 5 attempts remaining
123. Q5: - Find the equivalent resistance seen by the source, then calculate the power delivered by the source. (8) w- 600 Ω Pal Ө 2 ΚΩ 65 V 900 2: 750 ΩΣ 500 Ω w 1.5 ΚΩ 3 ΚΩ

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS