1. A Rankine cycle with reheating has a throttle pressure of 135 bars at the turbine inlet and 28 bars reheat pressure, the throttle and reheat temperature of the steam is 550C, condenser pressure is 0.035 bar, mass flow rate of steam is 10 kg/sec. Draw the T-s and schematic diagram of the cycle and determine the following: (c) theoretical thermal efficiency (d) the steam rate (e) heat rate of the cycle

1. A Rankine cycle with reheating has a throttle pressure of 135 bars at the turbine inlet and 28 bars reheat pressure, the throttle and reheat temperature of the steam is 550C, condenser pressure is 0.035 bar, mass flow rate of steam is 10 kg/sec. Draw the T-s and schematic diagram of the cycle and determine the following: (c) theoretical thermal efficiency (d) the steam rate (e) heat rate of the cycle

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

HMW-1 Regenerative steam power plant shown in figure below employs two feed heaters which are optimally placed such that cycle has the maximum thermal efficiency. The mass of steam generated is 16 kg/s. The feed water leaves each heater as saturated liquid at corresponding bleed pressure. Neglect the pumps work and find: a. Cycle thermal efficiency. b. Specific steam consumption. c. Mechanical efficiency of the turbine-generator gearing unit. Draw the equivalent (T-s) diagram considering an ideal cycle. 70 bar 450°C Gearing unit Generator 15 MW Turbine Super heater Boiler Condenser 0.07 bar Оpen heater Closed heater Pump Pump Throttling Valve
A steam turbine is to operate on a simple regenerative cycle. Steam is supplied dry saturated at 40 bar, and is exhausted to a condenser at 0.07 bar. The condensate is pumped to a pressure of 3.5 bar at which it is mixed with bleed steam from the turbine at 3.5 bar. The resulting water which is at saturation temperature is then pumped to the boiler. For the ideal cycle sketch the process on the T-s diagram and calculate, neglecting feed pump work,The amount of bleed steam required per kg of supply steamThe thermal efficiency of the plantThe specific steam consumption
stage Q2. At a stage of reaction turbine, the mean rotor diameter is 1.4 m. The speed ratio is 0.7. Determine the blade inlet angle if the blade outlet angle is 20°. The rotor speed is 3000 rpm. Also find the stage efficiency. Find the stage efficiency and rotor speed if the rotor is designed to run at the best theoretical speed ratio. Assume Parsons turbine and expansion losses as 10 % of heat drop. (50°, 90%, 90%)
Water is the working fluid in an ideal regenerative Rankine cycle with one open feedwater heater. Steam enters the turbine at 1400 lbf/in.² and 1000°F and expands to 120 lbf/in.2, where some of the steam is extracted and diverted to the open feedwater heater operating at 120 lbf/in.2 The remaining steam expands through the second-stage turbine to the condenser pressure of 2 lbf/in.² Saturated liquid exits the open feedwater heater at 120 lbf/in.² The net power output of the cycle is 1 x 10³ Btu/h. Determine for the cycle: (a) the mass flow rate of steam entering the first stage of the turbine, in lb/h. (b) the rate of heat transfer, in Btu/h, to the working fluid passing through the steam generator. (c) the percent thermal efficiency.
Water is the working fluid in an ideal regenerative Rankine cycle with one closed feedwater heater. Steam enters the turbine at 1400 lbf/in.2 and 1200°F and expands to 120 lbf/in.2, where some of the steam is extracted and diverted to the closed feedwater heater. The remaining steam expands through the second-stage turbine to the condenser pressure of 2 lbf/in.2 Condensate exiting the feedwater heater as saturated liquid at 120 lbf/in.2 undergoes a throttling process as it passes through a trap into the condenser. The feedwater leaves the heater at 1400 lbf/in.2 and a temperature equal to the saturation temperature at 120 lbf/in.2 The net power output of the cycle is 288 MW. Determine for the cycle:(a) the mass flow rate of steam entering the first stage of the turbine, in lb/h.(b) the rate of heat transfer, in Btu/h, to the working fluid passing through the steam generator.(c) the percent thermal efficiency.
compressing it isothermally. Determine the required change in pressure. 2-45 Saturated refrigerant-134a liquid at 10°C is cooled to 0°C at constant pressure. Using coefficient of volume expan- sion data, determine the change in the density of the refrigerant.
A pipeline with a pump carrying a 50 L/s discharge leads to a nozzle as shown. If the 180 mm diameter pipe is made of cast iron while the 120 mm diameter pipe is made of commercial steel. Determine the head of the pump using the energy equation from pt. A to pt. C. The fluid is water with a kinematic viscosity of 1.02 x 10-6 m³/s. El. 20 m Water B 180-mm dia. pipe 200-m long pipe 300-m long pipe 120-mm dia. pipe El. 10 m El. 30 m
The inlet and exit temperatures of the air expanded at an adiabatic turbine are 50 Cand -30 C, respctively, while operating at a plant. The air enters the turbine with a volumetric flow rate of 25 L/s and at 450 kPa. Assume air behaves as an ideal gas with constant specific heats. Calculate the turbine power output (kW) at isentropic conditions if the turbine operates at isentropic efficiency of 75%?
Consider a regenerative vapor Power cycle with one Feed water Heater the upper and lower limits of cycle 3.45 Mpa and 14 kpa respectively. Steam enters the high Pressure Turbine at 371c and leaves at 690Kpa , At which point Some of the steam is extracted and rejected to an open feed Water heater the remaining steam is expanded in the low Pressure turbine to 14 KPa Determine the Thermal efficiency if the isentropic efficiency of pump and turbine is 100%.
• A 6 MW generator had a thrust of 103,000 lb. The outside diameter of the step bearing is 12 in, and the inside diameter is 8 in. Employ a film thickness of 0.004 in. Use SAE 20 oil at 120 , the specific heat of the oil being 0.6 BTU/lb deg F, and density of 0.307 Ib/cu. in • Determine: (a) the flow rate in gallons / minute (b) Frictional loss only need b
4. An ideal vapor-compression heat pump cycle with Refrigerant 134a as the working fluid provides 15 kw to maintain a building at 200°C when the outside temperature is 50°C. Saturated vapor at 2.4 bar leaves the evaporator, and saturated liquid at 8 bar leaves the condenser. Calculate (a) The power input to the compressor, in kW (b) The coefficient of performance. (c) The coefficient of performance of a reversible heat pump cycle operating between thermal reservoirs at 20 and 50°C. (h, = 244.09kJ/kg, s, = 0.9222 kl/kg – K; h2 = 268.97 kJ/ kg; h, = 93.42 kJ/ kg) %3D
A Carnot vapor refrigeration cycle operates between thermal reservoirs at 7°C and 28°C. The working fluid is saturated vapor at the end of the compression process and saturated liquid at the beginning of the expansion process. Determine the operating pressures in the condenser and evaporator, in bar, and the coefficient of performance for each of the following as the working fluid. (a) Refrigerant 134a (b) Refrigerant R22 (c) water (d) ammonia