Refrigerant-134a is throttled from the saturated liquid state at 850 kPa to a pressure of 200 kPa. Determinethe temperature drop during this process and the final specific volume of the refrigerant.P₁ = 850 kPaSat. liquid규R-134aP₂ = 200 kPa

Answered: Image /qna-images/answer/95a1f536-6556-4b4d-9a6a-9c92679d0ed3.jpg

Answered: Refrigerant-134a is throttled from the…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Within few minutes
A piston-cylinder assembly contains ammonia, initially at a temperature of -20°C and a quality of 60%. The ammonia is slowly heated to a final state where the pressure is 6 bar and the temperature is 140°C. While the ammonia is heated, its pressure varies linearly with specific volume. For the ammonia, determine the work and heat transfer, each in kJ/kg.
A small lake with volume 10,000 m3 has a stream flowing into it with flow rate 100 m3/day and a Toluene concentration of 1.0 mg/m3. A factory discharges 5 m3/day into the lake with Toluene concentration of 10 mg/m3 – they want to increase effluent to 50 mg/m3. Toluene decays at a rate of 0.01/day. Assume steady-state and completely mixed (CSTR). a) How would this increase in discharge concentration change the lake concentration? b) Field studies show that the same lake would be better represented by dividing the lake into two cells. The first cell having a volume of 2,500 m3 and the second with 7,500 m3. How does this affect the estimate of concentration leaving the lake? Compare with one-cell model.Assume the factory continues to discharge at 10 mg/m3 into the first cell.c) Why does modeling the lake as multiple cells impact the final concentration leaving the lake? What do you expect might happen to the final concentration leaving the lake if we modeled it as more cells? How would…
I need solution on page plz
A piston compresses an ideal gas originally at P1, V₁ in an isothermal polytropic process (n=1) to one quarter its original volume. (a) Draw the CM and write the first law for this process. (b) Find the work, heat transfer, and internal energy change.
Two lbs of water vapor in a piston-cylinder assembly expands at a constant pressure of 250 lb/in² from a saturated vapor state to a volume of 7.08 ft³. Determine the initial and final temperatures, in °F, and the work for the process, in Btu.
Small droplets of carbon tetrachloride at 68 °F are formed with a spray nozzle. If the average diameter of the droplets is 280 µm what is the difference in pressure between the inside and outside of the droplets? Pa
A vapor compression refrigeration cycle uses steam as the working fluid. Steamflows steadily with a mass ow rate of 0.5 kg/s. Saturated vapor at 2.0 o C (State 1) enters an uninsulated compressor and it is compressed to 0.35 bar (State 2). Heat transfer at the rate of 105 kJ/s occurs from the compressor to its surroundings and the heat transfer exactly balances the entropy generation rate so that s2 = s1. The boundary and surrounding temperature of the compressor is measured to be 26.67 o C. Steam exits as saturated liquid at 0.34 bar (State 3) from the condenser. Steam leaving the condenser is then throttled in an expansion valve (State 4) before entering a constant pressure evaporator to complete the thermodynamic cycle. (a) Calculate the power (kJ/s) for the compressor. (b) Determine the isentropic efficiency (%) of the compressor. (c) Calculate the entropy generation for the compressor. (d) Find the coefficient of performance of the refrigeration cycle. (e) Show the cycle on T-s…
The sulfur dioxide (SO 2 ) stack gas concentration from fossil fuel combustion is 2 ppmv. Determine the stack gas SO2 concentration in units of ug/m 3 . Assume 0°C and 1 atm pressure.
Small droplets of carbon tetrachloride at 68 °F are formed with a spray nozzle. If the average diameter of the droplets is 300 μm what is the difference in pressure between the inside and outside of the droplets? Pa
Kerosene has a specific weight of γk = 51.1 lb/ft3 and benzene has a specific weight of γb = 56.2 lb/ft3. A.Determine the weight of kerosene that should be mixed with 8 lb of benzene so that the combined mixture has a specific weight of 52 lb/ft3
Problem 7 - 69 Gasoline at 20°C (sp. gr. 0.719, u = 0.000292 Pa-s) flows at the rate of 2 L/s through a pipe having an inside diameter of 60 mm Determine the Reynolds number Ans: 104.400

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Refrigerant-134a is throttled from the saturated liquid state at 850 kPa to a pressure of 200 kPa. Determine the temperature drop during this process and the final specific volume of the refrigerant. P₁ = 850 kPa Sat. liquid 규 R-134a P₂ = 200 kPa