Question 3 A 2L, 4-stroke, 4-cylinder petrol engine has a power output of 113.9 kW at 5500 rpm and a maximum torque of 235 N-m at 3000 rpm. When the engine is maintained to run at 5500 rpm, the compression ratio and the mechanical efficiency are measured to be 8.9 and 83.2%, respectively. Also, the volumetric efficiency is 93.1 %, and the indicated thermal efficiency is 43.76 %. The intake conditions are at 36.9 °C and 1.00 bar, and the calorific value of the fuel is 44 MJ/kg- Determine the Air-Fuel ratio in kg/kgf at 5500 rpm. Use four (4) decimal places in your solution and answer.

Question 3 A 2L, 4-stroke, 4-cylinder petrol engine has a power output of 113.9 kW at 5500 rpm and a maximum torque of 235 N-m at 3000 rpm. When the engine is maintained to run at 5500 rpm, the compression ratio and the mechanical efficiency are measured to be 8.9 and 83.2%, respectively. Also, the volumetric efficiency is 93.1 %, and the indicated thermal efficiency is 43.76 %. The intake conditions are at 36.9 °C and 1.00 bar, and the calorific value of the fuel is 44 MJ/kg- Determine the Air-Fuel ratio in kg/kgf at 5500 rpm. Use four (4) decimal places in your solution and answer.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Above is a pressure vessel with air in the form of gas. If the pressure vessel is used in the air vehicle, please provide at least two recommendations that can be applied in the system to ensure that the gas pressure inside does not change in the event of a temperature change due to a change in altitude
I need the answer as soon as possible
For the tank, calculate the volumetric flow of water, exiting the nozzle. the tank is sealed and there is a pressure of 20 psig on the water. depth h is 8 feet
As shown in the figure, a 300-ft³ tank contains 25 lb of H₂O initially at 30 lbf/in². The tank is connected to a large steam line carrying steam at 200 lbf/in2, 450°F. Steam flows into the tank through a valve until the tank pressure reaches p2 = 140 lbf/in² and the temperature is 400°F, at which time the valve is closed. Steam at 200 lbf/in.2, 450°F Valve (1) Tank Initially: 30 lbfin.², m₁ = 25 lb (2) Finally: P₂ lbfin.², 400°F. Determine the amount of mass that enters the tank, in lb, and the heat transfer to the tank from its surroundings, in Btu.
Show your entire and complete solution.
Q9: In a test on a two- stroke, heavy oil, marine engine, the following observations were made, Oil consumption, 4.05 kg; Calorific value of oil, 43000 kj/kg; het brake load 579N; Mean brake diameter, 1 m; mean effective pressure 275 kN/ m2; Cylinder diameter 0.20m; stroke, 0.250m; speed, 360 rpm. Icalculate o @ the mechanical efficiency the indicated thermal efficiency O Ihe brake thermal efficiency and The quantity of jacket water required per minute if 30% of the energy supplied by the fuel is absorbed by this water daisl a zgaus Permissible rise in temperature is 20k and specific heat capacity of water=D4.1868
Assuming smooth contact surfaces, determine the reactions A, B, C and D on the cylinders as shown in the fig. Show your solutions in two ways. W 200 lb We400 lb to 5.6'
A fluid is said to be ideal, if it is (a) incompressible (b) inviscous (c) viscous and incompressible (d) inviscous and compressible (e) inviscous and incompressible. C O A OB O E O D
The 1.9-Mg car increases its speed uniformly from rest to 17 m/s in 28 s up the inclined road. Part A Determine the maximum power that must be supplied by the engine, which operates with an efficiency of € = 0.8. (Figure 1) Express your answer with the appropriate units. Figure 10 ? ΜΑ Pmax = Value Units 1 of 1 Submit Request Answer Part B Also, find the average power supplied by the engine Express your answer with the appropriate units. HA ? Pavg= Value Units
1- A (completely closed) cylindrical shape tank, made of galvanized plate-steel of height 2.75 m and of diameter 2.8 m. If we want to make another (completely closed) rectangular shape tank of the same ( capacity and height) and of base width 1.95 m with the same material (galvanized plate-steel). Estimate the quantity of the required galvanized plate-steel in (m²) and compare it with the used quantity of the first tank.