Air within a piston-cylinder assembly, initially at 15 lbf/ in.2, 510°R, and a volume of 6 ft3, is compressed isentropically to a final volume of 3 ft³. Assuming the ideal gas model with k = 1.4 for the air, determine the: (a) mass, in lb. (b) final pressure, in lbf/in.2 (c) final temperature, in °R. (d) work, in Btu.

Air within a piston-cylinder assembly, initially at 15 lbf/ in.2, 510°R, and a volume of 6 ft3, is compressed isentropically to a final volume of 3 ft³. Assuming the ideal gas model with k = 1.4 for the air, determine the: (a) mass, in lb. (b) final pressure, in lbf/in.2 (c) final temperature, in °R. (d) work, in Btu.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 3 Bi As shown in the figure below, a weight (0.225 m³) is added to the top of the piston (5 kg); both the added weight and the piston adds pressure to the oil (SG = 0.85) in a circular tank. The tank has a diameter (D₁) of 0.6 m. The oil in the tank has a height (h₁) of 1 m. An open-end pipe is connected to the oil tank from the bottom of the tank. The oil surface in the pipe is 1.5 m (h₂) above the oil surface in the tank. What is the density of the weight? Weight Piston hi W D₁ Oil
6. A liquid having a Reynolds number 1900 flows through a 200 mm diameter pipe, 150 m long. The head loss of the pipe due to friction is 22 m. Ź a. Compute the friction factor b. Compute the kinematic viscosity of the liquid in sqm/sec. ( c. Compute the rate of flow in liters per hour
The 275-kg circular craft is suspended 100 mm from the ground. For this to occur, air is drawn in at 18 m/s through the 200-mm-diameter intake and discharged to the ground as shown. Take Pu = 1.22 kg/m³. Assume the fluid is an ideal fluid, that is, incompressible and frictionless. (Figure 1) -1.5 m -1.5 m -200 mm B 100 mm Determine the pressure that the craft exerts on the ground. Express your answer to three significant figures and include the appropriate units.
Fluid Mechanics. Reg.no : 5393 Pb # 3: Refer to Figure 2. Assume that friction is negligible, that θ = 115o, and that the water jet has a velocity of (Reg.No/100) m/s and a diameter of 60 mm. Find (a) the component of the force acting on the blade in the direction of the jet; (b) the force component normal to the jet; and (c) the magnitude and direction of the resultant force exerted on the blade. Note: Assume reasonable values for any missing data. Symbols have usual meaning unless otherwise stated.
4. The pressure intensity at a point in a fluid is given 4.9 N/cm². Find the corresponding height of fluid when it 5. An oil of sp. gr. 0.8 is contained in a vessel. At a point the height of oil is 20 m. Find the corresponding m [Ans. (a) 5 m of water, (b) 6.25 m of cil is : (a) water, and (b) an oil of sp. gr. 0.8. (Ans. 16 m) and pbove it an oil of sp. gr. 0.8 for a depth of 2 m height of water at that point.
•Determine the unit weight of the liquid when it is at the level shown. (Express the answer in English unit) •Determine the weight of the liquid. (Express the answer in English unit) •Assuming no mixing of liquids occur, if glycerin (SG= 1.26) is poured into the tank: a.) it will sink to the bottom of the tank b.) it will float on the surface of the liquid c.) it will be suspended in the liquid * answer should be in 3 decimal places
Air with a mass flow rate of 5 kg/s enters a horizontal nozzle operating at steady state at 450 K, 350 kPa, and velocity of 3 m/s. The nozzle is well insulated. At the exit, pressure is 300 kPa and temperature is 390 K. Using the ideal gas model for air, the area at the inlet is m², and the velocity at the outlet is Are potential effects negligible? Why? m/s. Is heat transfer negligible? Why? Note that you may choose to model the specific heat as constant.
A U-tube of uniform cross-section has both arms open to the atmosphere. The U-tube contains three immiscible liquids, with density PA, PB, and pc, as depicted in the diagram below, where po is the atmospheric pressure. We denote h to be the depth of the open surface of liquid A on the left arm, relative to the open surface of liquid Con the right arm. I is the depth of the interface between liquid B and C on the right arm and 2l is the depth of the interface between liquid A and liquid B on the right arm. Po PA (c) Po PC PB е е (a) Explain why the liquid densities need to satisfy the condition PA PB PC. (b) Write down an expression for the pressure at depth z below the surface of liquid A in the left-hand part of the tube. Show that l < h < 2l if PB + PC < PA•
A Cylindrical Can open at one end is 20 cm in diameter and 40 cm long. The can welghs 6 N. The can is carefully put in a large tank of water vertically, with 20 cm its open end down so that the air is trapped in It (as shown in given figure). If the air in it can be assumed to undergo 40 cm isothermal compression, calculate the elevations of the water surface inside the Can and the top of the Can relative to the water surface in the tank. The atmospheric pressure is 100 kPa and the temperature is 20°C. (Take : = 9810 N/m³]
5-64. A thin rubber tube of 25 mm inside diameter is used to siphon water from the large tank of Figure 5.56. To prevent the tube from collapsing, the pressure inside the tube can not be less than 50% of the pressure outside the tube. Determine the smallest value of h to prevent the siphon from stopping due to collapsing of the tube. 2.5 m 5 m Figure 5.56 System for Exercise 5-64. THANK SUNTETICE Full Michifo Nas s itset SCH
Air in a room at T0 = 290 K and P0 = 90 kPa is to be drawn by a vacuum pump through a 3-cm-diameter, 2-m-long adiabatic tube equipped with a converging nozzle at the inlet. The flow in the nozzle section can be approximated as isentropic. The static pressure is measured to be 87 kPa at the tube inlet and 55 kPa at the tube exit. Determine the mass flow rate of air through the duct, the air velocity at the duct exit, and the average friction factor for the duct.