An ideal vapor-compression heat pump cycle with Refrigerant 134a as the working fluid provides 15 kW to maintain a building at 200°C when the outside temperature is 50°c. Saturated vapor at 2.4 bar leaves the evaporator, and saturated liquid at 8 bar leaves the condenser. Calculate (a) The power input to the compressor, in kW (b) The coefficient of performance. (c) The coefficient of performance of a reversible heat pump cycle operating between thermal reservoirs at 20 and 50°c. (h, = 244.09ki/kg, s, = 0.9222 kJ/kg – K; h2 = 268.97 kJ/ kg; h, = 93.42 kJ/ kg)

An ideal vapor-compression heat pump cycle with Refrigerant 134a as the working fluid provides 15 kW to maintain a building at 200°C when the outside temperature is 50°c. Saturated vapor at 2.4 bar leaves the evaporator, and saturated liquid at 8 bar leaves the condenser. Calculate (a) The power input to the compressor, in kW (b) The coefficient of performance. (c) The coefficient of performance of a reversible heat pump cycle operating between thermal reservoirs at 20 and 50°c. (h, = 244.09ki/kg, s, = 0.9222 kJ/kg – K; h2 = 268.97 kJ/ kg; h, = 93.42 kJ/ kg)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A Carnot vapor refrigeration cycle operates between thermal reservoirs at 7°C and 28°C. The working fluid is saturated vapor at the end of the compression process and saturated liquid at the beginning of the expansion process. Determine the operating pressures in the condenser and evaporator, in bar, and the coefficient of performance for each of the following as the working fluid. (a) Refrigerant 134a (b) Refrigerant R22 (c) water (d) ammonia
The piping of the circuit in Figure is modified as follows. First, the pipeline from the upper discharge port of the directional control valve is connected to the rod end of the cylinder. Then the pipeline from the lower discharge port of the directional control valve is connected to the blank end of the cylinder. What effect does this have on the minimum flow capacity of the return line filter?
I need the answer as soon as possible
2.6 An open tank contains water upto a de pth of 2 m and above it an oil of sp. gr. 0.9 for a depih of 1 m. Find the pressure intensity (i) at the interface of the two liquids, and (ii) at the bottom of the tank.
Steam at a pressure of 0.08 bar and a quality of 99.0% enters a shell-and-tube heat exchanger where it condenses on the outside of tubes through which cooling water flows, exiting as saturated liquid at 0.08 bar. The mass flow rate of the condensing steam is 5.8 x 105 kg/h. Cooling water enters the tubes at 15°C and exits at 35°C with negligible change in pressure. Neglecting stray heat transfer and ignoring kinetic and potential energy effects, determine the mass flow rate of the cooling water, in kg/h, for steady-state operation. mwater = i 568765.92 kg/h
Need asap
A constant-area duct that is 20 cm in length by 2 cm in diameter is connected to a reservoir through a converging nozzle, as shown in Figure 9.13. For a reservoir pressure and tem- perature of 1 MPa and 500 K, determine the maximum air flow rate in kilograms per sec- ond through the system and the range of back pressures over which this flow is realized. Repeat these calculations for a converging nozzle with no duct. Assume that fis equal to 0.032 and that y - 1.4. f= 0.032 D-2 cm Isentropic flow P1,000 kPa I 500 K 20 cm