A pipeline with a pump carrying a 50 L/s discharge leads to a nozzle as shown. If the 180 mm diameter pipe is made of cast iron while the 120 mm diameter pipe is made of commercial steel. Determine the head of the pump using the energy equation from pt. A to pt. C. The fluid is water with a kinematic viscosity of 1.02 x 10-6 m³/s. El. 20 m Water B 180-mm dia. pipe 200-m long pipe 300-m long pipe 120-mm dia. pipe El. 10 m El. 30 m

A pipeline with a pump carrying a 50 L/s discharge leads to a nozzle as shown. If the 180 mm diameter pipe is made of cast iron while the 120 mm diameter pipe is made of commercial steel. Determine the head of the pump using the energy equation from pt. A to pt. C. The fluid is water with a kinematic viscosity of 1.02 x 10-6 m³/s. El. 20 m Water B 180-mm dia. pipe 200-m long pipe 300-m long pipe 120-mm dia. pipe El. 10 m El. 30 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

•Determine the unit weight of the liquid when it is at the level shown. (Express the answer in English unit) •Determine the weight of the liquid. (Express the answer in English unit) •Assuming no mixing of liquids occur, if glycerin (SG= 1.26) is poured into the tank: a.) it will sink to the bottom of the tank b.) it will float on the surface of the liquid c.) it will be suspended in the liquid * answer should be in 3 decimal places
(b) A water turbine model is constructed at ratio of 1:8 with power system of 10 kW at speed of 555 rpm under a head of 2.5 m. Overall efficiency for both model and prototype is assumed at 0.93. (i) Detemine the specifie speed. mine t); (ii) If the prototype is run under a head of 25 m, calculate its rotational speed, power and discharge.
2. Given the figure below, solve for flow rate in the venturi meter. (C = 0.984) 2 (ø - 250mm) 0.3m oil (as2) 0.8m - glycerin (1.86)
Exercise#3: The figure shows a system. The system is conservative energy between the two valves CV, and CV2. The differential pressure element at point 1 shows a reading for flow rate. This flow rate is equivalent to AP = 3 mmH20 with k factor of orifice equals 20 m² (used as dimension geometry for the pipe). Another turbine flow meter at point 4 shows a reading for flow rate equals 2.7. Based on the reading of the first flow meter, is the turbine flow meter give the correct reading or not? You can utilize the following given information: diameters at point1&2 are D, = D2 = 0.2 m, Dz = D4 = 2 D2, Q1= 3Q2, P4 = P3 – 200000 Pa ,p = 750 Total heads(or energy)of Bernoulli equation at point 1=Total heads(or energy)of Bernoulli equation at point 2+4m, and point2 point1 Total heads(or energy) of Bernoulli equation at point 3=Total heads(or energy) of Bernoulli equation at point 4+10m. CV, 8 Closed DP · Flow meter h tank Turbine Flowmeter CV2 voint4 point3
The pump draws oil with specific gravity of 0.90 from a reservoir and delivers it to the hydraulic cylinder. The cylinder has an inside diameter of 5.0 inch and in 15 seconds the piston must travel 20 inches while exerting a force of 11,000 lb. It is estimated that there are energy losses of 11.5 lb-ft/lb in the suction pipe and 35.0 lb-ft/lb in the discharge pipe. Both pipes are 3/8-in Scheulde 80 steel pipe with inside diameter of 0.423 inch. Calculate the pressure at the cylinder.
PLEASE ANSWER ASAP. WILL UPVOTE. PLEASE HELP
Question is in figure
Fluid 5