PROBLEM 6 Sketch the EGL and HGL for the system shown below and label with the energy heads. Include the minor losses. Conditions: (a) da < de > de (b) Nozzle is discharging to atmosphere (c) Include minor loss (fitting) nozzle fitting Pipe c Pipe A Pipe B Pump Datum

PROBLEM 6 Sketch the EGL and HGL for the system shown below and label with the energy heads. Include the minor losses. Conditions: (a) da < de > de (b) Nozzle is discharging to atmosphere (c) Include minor loss (fitting) nozzle fitting Pipe c Pipe A Pipe B Pump Datum

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The centrifugal pump has to work with the following specifications: Static suction head: 3 m Static delivery head: 8 m Length of suction pipe: 7m Length of delivery pipe: 10 m Discharge: 850 lpm Working fluid: Water at 30°C A3 The pump is directly connected to an electric motor. Design the pump completely for pumping water.
9- a) b) c) d) For the transmission line shown, what are the appropriate appurtenance at point C. 300 m A L = 500 m B none of them air valve check valve blowoff Leave blank L = 1000 m 100 m 285 m L = 1000 m D 100 m
HMW-1 Regenerative steam power plant shown in figure below employs two feed heaters which are optimally placed such that cycle has the maximum thermal efficiency. The mass of steam generated is 16 kg/s. The feed water leaves each heater as saturated liquid at corresponding bleed pressure. Neglect the pumps work and find: a. Cycle thermal efficiency. b. Specific steam consumption. c. Mechanical efficiency of the turbine-generator gearing unit. Draw the equivalent (T-s) diagram considering an ideal cycle. 70 bar 450°C Gearing unit Generator 15 MW Turbine Super heater Boiler Condenser 0.07 bar Оpen heater Closed heater Pump Pump Throttling Valve
I need the answer as soon as possible
Q1/ liquid is pumped from a ground 90 elbow 90° For this system: - (Le/d) of globe valve = 240 (Le/d) of 90" elbow = 40 (Le/d) of 45" elbow - 18 h: of Heat Exchanger 1 = 2.2 m of liq. Fof Heat Exchanger 2 = 25 J/kg Pump efficiency elbow level reservoir to an overhead tank H.Ex.2 through a 15 cm ID pipes of e/d = 0.018 as shown in figure: i. What is the pressure developed by the pump to supply water to Tank Globe Valve 45" elbow - 62 % Pump the tank at the rate of 960 45° elbow /min? ii. What is the power required for the pump? Given that: u = 1.6 cP; sp.gr 0.86; and the lengths as follow; L = 33 m, L2 = 17 m, L3 = 8 m, L4 = 35 m Reservair H.Ex.1
Design an ESP that is 98,5% efficient in treating 8050 m3/min of gas, Assume the plates are 6.1 m high and 4.1 m long. The effective drift velocity of the particles is 5.2 m/imn. The design should include the plate design (total area, layout, number), channel width, gas velocity, number of ducts, aspect ratio, number of mechanical fields and number of electrical sections total, and actual area.
1. A Rankine cycle with reheating has a throttle pressure of 135 bars at the turbine inlet and 28 bars reheat pressure, the throttle and reheat temperature of the steam is 550C, condenser pressure is 0.035 bar, mass flow rate of steam is 10 kg/sec. Draw the T-s and schematic diagram of the cycle and determine the following: (c) theoretical thermal efficiency (d) the steam rate (e) heat rate of the cycle
Q5: For the piping shown in Fig. (6), calculate the flow rate and minimum pressure if H=30m. (f-0.024 ;Kentrance-0.5; Kvalve-5; Kexit-1.0). Water 20°C 20 m 2 cm dia. 40 m Angle valve (wide open) H 4 cm dia. 2m f
Design a pipe to supply water from the elevated tank to the demand point at a discharge rate of 0.05 m3/s. Use Galvanized Iron pipe and assume water temperature as 15°C. Minor losses can be neglected due to smooth transitions.
Task 3: Fluid Mechanics Lab Meters You studied the SAYBOLT viscometer in the fluid mechanics lab to determine 20W50 Motor Oil viscosity. Follow the following steps to do your task.
I need the answer quickly