A steel bar 30 mm in diameter and 2 m long is encased in a shell of cast iron 5 mm thick. Compute the stress in each material, in MPa, if a compressive axial load of 150 kN is applied to the assembly. For steel, E = 200 MPa and for cast iron, E = 100 %3D GPa ( Select the correct response(s): 29.96 MPa 76.39 MPa 212.21 MPa 106.10 MPa 136.32 MPa 152.79 MPa 59.92 MPa 272.84 MPa

A steel bar 30 mm in diameter and 2 m long is encased in a shell of cast iron 5 mm thick. Compute the stress in each material, in MPa, if a compressive axial load of 150 kN is applied to the assembly. For steel, E = 200 MPa and for cast iron, E = 100 %3D GPa ( Select the correct response(s): 29.96 MPa 76.39 MPa 212.21 MPa 106.10 MPa 136.32 MPa 152.79 MPa 59.92 MPa 272.84 MPa

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

3) An bronze rod is rigidly attached between a aluminum rod and a steel rod as shown. Axial loads are applied at the positions indicated. Find the maximum allowable value of P that will not exceed a stress in steel of 140MPA, in aluminum of 90MPA or in bronze of 100MPа. Aluminum A = 500mm? Bronze A = 200mm? Steel A = 150mm2 2P ЗР L st = 1.2m L br = 2m Lal = 3.5m
The shown plate is 60 mm thick and it is made of Magnesium Am1004-T61. The plate is fitted between the rigid frictionless supports as shown and at T, = 20°C it is stress free. Find the stresses in the x and y directions when the temperature increases to T, = 58°C. %3D 150 mm 150 mm Select one: O x: 0 MPa, y: 42.864 MPa Ox: 22.1 MPa, y: 44.2 MPa Ox: 0 MPa, y: 44.2 MPa Ox: 0 MPa, y: 17.8 MPa O x: 13.2 MPa, y: 44.2 MPa Ox: 0 MPa, y: 67.4 MPa 3:10 PM O G 4) ENG 1/31/2021
Q # 4: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Figure. Axial loads are applied at the positions indicated. The value of P is limited to 20 KN in bronze, 72 KN in aluminum and 28 KN in steel Find the area of each section that will not exceed a stress in steel of 280 MPa, in aluminum of 180 MPa, or in bronze of 200 MPa. CLO -2 Steel Aluminum Bronze 2P 4P 2.5 2.0 1.5
An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa. Steel Aluminum Bronze A- 500mm? A = 400mm? A - 200mm 40KN 10KN 20KN 2.5m 2.0m 1.5m
An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Fig. P-108. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 90 MPa, or in bronze of 100 MPa. Figure P-108 PARTNER Aluminum A=400 mm² Steel A = 500 mm² 2.5 m 2.0 m Bronze A = 200 mm² 1.5 m 2P
An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 1) What is the deformation 8Ag in mm? 10KN 0.8m 0.4m 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
2. A rod is composed of an aluminum section rigidly attached between steel and bronze sections as shown in the figure. Axial loads are applied at the positions indicated. The cross-sectional area of the rod is 300sq.mm. Express your answer in MPa. Determine the stress in the steel. b. a. Determine the stress in the aluminum. Determine the stress in the bronze. C. STEEL ALUMINUM BRONZE 56kN 14kN -0.6m- -0.9m- -0.76m-
A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure. Axial loads are applied at the positions indicated. If P 4000 Ib and the cross-sectional area of the rod is 1.0 sq.in. What is %3D the stress in the bronze? (in ksi) Note: indicate sign (no sign means positive/tenslon) 4P Steel Bronze Aluminum 2 ft 3 ft 2.5 ft
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN. 0.8m 0.4m B 5KN 0.6m Al 20KN Q2 5) What is the deformation 8, in mm? A=800 mm? A=1,200 mm?
AN ALUMINUM TUBE IS FASTENED BETWEEN A STEEL ROD AND BRONZE ROD AS SHOWN IN THE FIGURE. AXIAL LOADS ARE APPLIED AT THE POSITIONS INDICATED. FIND THE VALUE OF P THAT WILL NOT EXCEED A MAXIMUM OVERALL DEFORMATION OF 5mm OR A STRESS IN THE STEEL OF 120MPa, IN BRONZE OF 130 MPa AND IN ALUMINUM OF 90 MPa. Modulus of Elasticty of Bronze = 80 GPa, Aluminum = 65 GPa and Steel = 210 GPa. 2P P 3P 4P L = 500mm 800 A = 400mm² 900 600 700 C
A ngid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D. as shown Neglect deflections of the bar due to bending Use E200 GPa What is the displacement of the loaded end of the bar? 2 Determine the tensile stress induced in rod CD by the 80 kN load the alowable stress in rod CD is 124 MPa, what weight W can be safely applied?
A hollow aluminum tube is rigidly attached between steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in aluminum of 80 MPa, in steel of 150 MPa or bronze of 100 MPa. Steel Aluminum Bronze А P> ЗР - 2P outside = 30 mm d inside = 20 mm d d = 16 mm d = 60 mm -100mm- -150mm- -125mm-