A beam cross-section is subjected to anaxial force P. Determine the application point of theload on the cross-section when the neutral axis passesthrough the points A and B as shown. Calculate P ifthe allowable normal stress is oallow = 280 MPa.- 15 cm3 cm12 cm3 cmNeutral axisB3 cm

Consider the given beam. The allowable stress is σallow=280 MPa.

Answered: A beam cross-section is subjected to an…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Part 2,3,4
The green triangle (initial state) experiences deformation transforming into red triangle (final state). Determine the axial strain in side XZ if XZ = 655 mm and XZ' = 729 MM. (UNITLESS)
A steel tube with the cross section shown is 3 m long and has a wall thickness of 4.8 mm. (a) If the allowable shear stress is 60 MPa, determine the largest torque that can be applied safely to the tube. (b) Compute the corresponding angle of twist. Use G = 80 GPa for steel. 90 mm 90 mm -90 mm --90 mm →
The ends of the compound shaft are attached to rigid walls. The maximum shear stress is limited to 60 MPa for the bronze segment AB and 84 MPa psi for the steel segment BC. Determine the diameter of each segment so that each material is simultaneously stressed to its permissible limit when the torque T = 40 kN-m is applied as shown. The shear moduli are 35 GPa for bronze and 80 GPa for steel. Bronze Steel B A T 3 m 2 m
Question # 4: Determine the state of stress at point A on the cross section at section a-a of the cantilever beam. Show the results in a differential element at the point. ( 2 m a 0.5m 400 KN 100 mm 300 mm 100 mm Section a-a
A flat steel bar, 26 mm wide by 2 mm thick and 1.8 m long, is bent by couples applied at the ends so that the midpoint deflection is 27 mm. Compute the maximum stress in the bar. Use E =220 GPa. Answer must be in MPa.
B) A steel rod with a cross sectional area of (12 mm 12 mm) is stretched between two fixed points. the tensil load at 20°C is 2 KN, what will be the stress at 5°C. assume a = 11.7*10 m/(m.°C) and E-200 Gpa.
Bar A has diameter 'd' and bar B has diameter '2d'. Both are of the same length and are of the same material. If they are subjected to same axial load P, the ratio of extension of bar A to B is (B) 2 (A) 4 (C) 0.5 (D) 0.25
A flat steel bar, 30 mm wide by 2 mm thick and 1.3 m long, is bent by couples applied at the ends so that the midpoint deflection is 27 mm. Compute the maximum stress in the bar. Use E = 220 GPa. Answer must be in MPa.
A flat steel bar, 26 mm wide by 3 mm thick and 1.7 m long, is bent by couples applied at the ends so that the midpoint deflection is 21 mm. Compute the maximum stress in the bar. Use E = 240 GPa. Answer must be in MPa.
The thin rectangular plate is uniformly deformed such that Ex = 220E, Ey= -680 uE, and yy = 870 urad. If a = 35 mm, determine (a) the normal strain &, in the plate. (b) the normal strain &, in the plate. (c) the shear strain ynt in the plate. B D. a a a a a a a a a Answers: (a) En= i HE (b) Et= i HE (c) Ynt = i prad

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

A beam cross-section is subjected to an axial force P. Determine the application point of the load on the cross-section when the neutral axis passes through the points A and B as shown. Calculate P if the allowable normal stress is oallow = 280 MPa. - 15 cm 3 cm 12 cm 3 cm Neutral axis B 3 cm