Defferentiate the following terms; 1.Resilience and proof resilience 2.proof resilience and modulus of resilience B)A solid beam ABC circular in section has varying sections.portion AB is 6m in length and diameter of 250mm while portion BC is 2m in length and section diameter of 100mm.The beam is subjected to a sudden tensile load.if the maximum stress induced is 400MN/m^2.Determine the strain energy stored in the beam.Take E=200GN/m^2

Q: Cross section of each bar 350 mm2 . Find stress in bar CD

A:

Q: A cast iron beam is of T-Section as shown in figure below. The beam is simply supported on a span of…

A:

Q: Fundamentals of Deformable Bodies The frame shown in figure shows three pinned end bars AB, BD, and…

A: Note:- AB is not any bar according to the given figure, taking AD as a third bar A frame is given…

Q: maximum value for the load R.

A:

Q: The cantilever T- beam is loaded as shown in the figure. Ti 80 mm 40 kN/m NA 120 mm 2.0 m INa =…

A: A loaded beam is given with its cross section and it has been asked to determine its compressive…

Q: AT section of a beam is fabricated from 2 - 12 mm x pined by welding as shown in Figure ST-904. It…

A: Data provided : Simply supported beam with partial UDL  T-Section    To find : 1) Maximum…

Q: A steel pipe is subjected to a quadratic distributed load over its height with the peak intensity qo…

A:

Q: 3. A concrete floor slab is reinforced by steel rods placed 38mm above the lower face of the slab…

A:

Q: A beam with a T-section is supported and loaded as shown in the figure. The cross section has width…

A: A beam with the T section is given in the question all the loading condition is given in the above…

Q: A column of square section 40 mm x 40 mm, fixed to the ground carries an eccentric load P of 1600 N…

A:

Q: The rigid platform shown has negligible mass and rests on two steel bars, each 250 mm long. The…

A:

Q: 4. The beam shown supports the load shown, determine max flexural stress developed and 200mm the max…

A:

Q: Determine the stress concentration factor for the beam shown below that has a fillet to the larger…

A: step 1-

Q: A cantilever beam with a ‘T’ shaped cross-section is loaded with a distributed load as shown below.…

A:

Q: An 8 m simple beam is loaded with a 208 kN point load at the first third of its length. The cross…

A: Given data: Load=208 kN  Allowable stress=200 MPaThickness=20 mm  Length=8m  c=333.333 mm Load=208…

Q: PROBLEM 1.3 75 mm 12AN Two solid cylindrical rods AB and BC are welded together at B and loaded as…

A:

Q: A cantilever beam QT having rectangular cross sections with varying width h, and varying height b,…

A:

Q: A simply supported beam is loaded by the couple M=2000 N-m as shoWH. TAE beam has a channel-type…

A:

Q: 2. The inverted T-section of a 4 m simply supported beam has the properties showr in the figure. The…

A:

Q: A cantilever beam with a ‘T’ shaped cross-section is loaded with a distributed load as shown below.…

A: GIven,A cantilever beam with a ‘T’ shaped cross-section is given in the Question Here,The intensity…

Q: A three part bar is connected to walls at D and C and loaded as shown. Middle section AB is solid…

A:

Q: A flat steel bar, 28 mm wide by 2 mm thick and 1.7 m long, is bent by couples applied at the ends so…

A: To find maximum stress in bar

Q: Three bars, hinged at A & D. pinned at B & Cas shown in Figure, form a four-link mechanism.…

A:

Q: 3. An ASTM A36 structural steel beam 5.00 m long is placed between two rigid supports. When the…

A: Given data,  ASTM A36 steel Length of beam = 5 m Initial temperature = 20° C Final temperature = 45…

Q: QUESTION: The distributed load on the T-section beam shown below and moment affects. A is the fixed…

A:

Q: A cantilever beam has a cross-section and concentrated loads P1 = 30 kN and P2 = 10 kN, as shown.…

A:

Q: Question 6 The reinforced concrete beam shown in Figure 6 is encastré at both ends. It supports a…

A: Calculation of vertical reactions

Q: Two bars are made of a material with the stress-strain diagram as shown. Find the cross-sectional…

A:

Q: Q2 The beam shown in Figure Q2 is loaded with a triangular distributed load from A to B, and a…

A:

Q: ind the diameter of dAB BC вс + bar if the stress equal t .15GPA 120cm B 125kN 125kN 90cm A 60KN

A:

Q: A beam ABC with an overhang from B toC supports a uniform load of 200 lb/ft throughout itslength…

A: Given:- uniform load=q=200 lb/ft a=12ft b=6ft L=18ft To find:- (a) the maximum tensile stress σt and…

Q: 2. The steel rod is stress-free before the axial loads P1 150 kN and P2 %3D %3D 90 kN are applied to…

A:

Q: A simply supported beam carries a concentrated load at the center which fluctuates from a value of W…

A: Assumptions of the theory of simple bending:  The material of the beam is homogenous and isotropic.…

Q: For the beam structure shown below the data is as follows: P= 9.6-kN, L = 6-m, d= 2.4-m, b=100-mm,…

A: Given data,  P =9.6 kN L = 6 m d = 2.4 m b = 100 mm t = 30 mm h = 150 mm h1 = 130 mm

Q: Question 3 A pair of lateral load is applied to a 3 m steel beam as in Figure Q3a to bend it…

A: L = 3m

Q: is applied over an entire length of a simply supported beam 8m long. The beam section is made up of…

A: Given:- L=8m  The beam section is made up of four 20mmx100mm rectangles  To find:- a. maximum value…

Q: Question 2) Find the shear center of the section below and calculate the maximum shear stress that…

A:

Q: 6 - A circular shaft is composed of a steel core and a brass covering, as shown in the figure. Under…

A:

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.