4) A simply supported beam supports the uniformly distributed load of intensity Wo. Determine the safe allowable value of Wo if the flexural stress is limited to 160 MPa in tension, 200 MPa in compression, shear stress is limited to 70 MPa and maximum allowable deflection is 15mm. The modulus of elasticity of the beam is 200 GPa. Use Moment Area Method. 1m Wo 3m 2m 30 230 MC 10 10 10 (dimensions in mm) 150

4) A simply supported beam supports the uniformly distributed load of intensity Wo. Determine the safe allowable value of Wo if the flexural stress is limited to 160 MPa in tension, 200 MPa in compression, shear stress is limited to 70 MPa and maximum allowable deflection is 15mm. The modulus of elasticity of the beam is 200 GPa. Use Moment Area Method. 1m Wo 3m 2m 30 230 MC 10 10 10 (dimensions in mm) 150

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Solve correctly
PLEASE PROVIDE COMPLETE SOLUTION THANKS
Instruction: Use 3 decimal places.
The beam shown is made of a nylon for which the allowable stress is 24MPa in tension and 31MPa in compression. Determine the largest couple M that can be applied to the beam. 24 mm 60 mm 30 mm 80 mm
C.engg. Soldi.mech.
3. An A36 Steel Cantilever Beam is shown below, also showing its cross section. Determine the following: Given the formula of the Maximum allowable bending stress of steel, fb = 0.66Fy. Where Fy is the Yield Stress of Steel. Where the bending stress for a beam is (fb) = Mc/I, where c is the distance of the centroid to the extreme most fiber of the beam (either top-most or bottom-most distance). Does the Steel fail under the loading given? Use Fy = 450 Mpa. Use the Moment in (a) and the moment of inertia in (c).
A square beam (w=0.03 m) is loaded with a point load of 1000 N and a moment load of 1000 Nm, as shown. i. Determine maximum deflection of the beam using step by step analytical equations. ii. Determine the Maximum stress in the beam using step by step analytical equations iii. For both top fibers and bottom fibers of the square beam, specify the type of the stresses.
The stiffness matrix of the beam shown below is - 1. (2 В El 2EI 4m 8m A.
Q4 (b) Figure Q4(a) shows a steel beam with length of 4 m that is supported by a steel column at point B. The steel column of AB has a rectangular cross section (40 mm× 70 mm). The ends are assumed to be pin connected. The yield stress of steel is o y 250 MPa. The Modulus Elasticity of the steel is 200 GPa. Use factor of safety of 1.5. (i) Check whether the Euler's equation is appropriate or not. (ii) Determine the maximum distributed load (W) that can be applied to the beam so that the column of AB does not buckle.
A rectangle column 500 mm x200 mm in cross-section is subjected to a compression load 1000 KN, the stress on the column is: a. 30 MPa b. 10 MPa C. 50 MPa d. 20 MPa
Q2: The simply supported beam shown as Figure 5. below is subjected to Loading as shown on the Figure. Using integration method. Find the maximum Lenght (L) so that the max. deflection is not greater than 30mm for the Beam.. The flexural rigidity (El) of Beam section El = 50*10% KN.m? “4m e | Sm