1. The structure shown below is subjected to a total uniform load w. The flexural stress in the steel section is limited to 150 MPa. Using conjugate beam method, determine the following: (a) Maximum total uniform load w that can be supported by the structure (b) Maximum shear stress, (c) Deflection at C (d) Slope at E. PL 100x10mm w 10x130mm PL 100x10mm SECTION 1 A B PL 100x5mm 5x140mm 2 m 1m 1 m 1m PL 100x5mm Section 1 Section 2 SECTION 2 Fig. 1

1. The structure shown below is subjected to a total uniform load w. The flexural stress in the steel section is limited to 150 MPa. Using conjugate beam method, determine the following: (a) Maximum total uniform load w that can be supported by the structure (b) Maximum shear stress, (c) Deflection at C (d) Slope at E. PL 100x10mm w 10x130mm PL 100x10mm SECTION 1 A B PL 100x5mm 5x140mm 2 m 1m 1 m 1m PL 100x5mm Section 1 Section 2 SECTION 2 Fig. 1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: wrw/m Lom

Q: Derive the deflection at different points of the beam, the maximum deflection, and slopes of the…

Q: The timber beam in Figure 2 is simply supported at points A and E. The cross-section of the beam…

Q: For the Beams Shown below solve each of the Following: Deflection at Points B C and D for the…

Q: Consider the beam shown in Egure 1) Take E-29(10) kxi. I-120 in Figure 100 10A 30 100 1001 Part B…

Q: analyze the shown beam using: 1- force method 2- stiffness method assume that A is pin support and B…

A: the truss using both the force method (method of joints) and the stiffness method.**1. Analyze the…

Q: [100 lb 80 lb A + 2 ft 4 ft 3 ft B.

Q: I rigidity, El, is loaded ad, w per unit length. flection of the beam is

Q: Using Double integration Method derive an expression for deflection at free end of the cantilever…

A: "Since you have asked multiple question you will solve the first for you.If you want any specific…

Q: Determine the maximum deflection of the beam. Assume that a wooden beam has a vertical deflection…

A: Ans is given below

Q: w = 24kn/m a = 15m E = 200 GPa I = 70 x 10^6 mm^4 Solve using conjugate beam method

Q: Determine the deflection at point C of the beam shown using Castigliano's Theorem. (You can verify…

Q: concentrated load of 8 kN at a distance of 3m from the right support. E = %3D 200 GPa and I =…

A: Double integration method Given simply support beam Span l = 12m Find Max deflection Max deflection…

Q: discuss the procedure on how to determine deflection using the following method: a. finite…

A: To discuss the procedure to determine deflection using the:a. finite difference methodb. conjugate…

Q: y using approximate method portal method, analyze the frame shown in figure below 100 kN H 7 m 50 kN…

Q: Part 2: Beam analysis The timber beam in Figure 2 is simply supported at points A and E. The…

A: Castigilano's TheormThe deflection is given by Now the reaction at the left and right support is ΣFy…

Q: A cantilever beam subjected to uniform variable load, if the beam is made of I Beam having a…

Q: I asked this question from my book before "Determine the equations of the elastic curve for the beam…

A: Step 1:Step 2:Step 3:Step 4:

Q: Deflection of Beams 1. Determine the midspan deflection of the beam if E = 10 GPa and I = 20 × 10“…

Q: Newton Raphson Method; f(x) = 5x + In x - 1000

A: To determine the root of the given function using the Newton Raphson method. Given: fx=5x+lnx-1000…

Q: The truss shown is one of several supporting an advertising panel. Consider the wind load P = 820 N…

A: Step 1:Step 2:Step 3:Step 4:

Q: Using double integration method deruve an expression for the deflection at free end of the…

Q: Write and explain Beam’s local balance equation

Q: The beam below is loaded as shown. Using double double integration method. Determine the following…

Q: nine the end deflection of this beam. Fill in the blanks. Hint: Solve two separate problems. One…

A: Given data:

Q: Derive at least 5 cases from the 12 cases of beam loadings that is shown. Using DOUBLE INTEGRATION…

A: Double integration method : This method is useful when uniform bending moment equation is applicable…

Q: Create a non-prismatic beam and use area moment method to solve it(Show complete solution)

A: Given: A non prismatic beam with loading To find: Slope and deflection by moment area method Note:…

Q: 2. Derive an equation that describes the vertical deflection of the beam, y(x), and also calculate…

Q: This "I-shaped" cross-section is often used for beams because the moment of inertia about the…

A: Given data Find moment of inertia about strong axis (I) using subtractive method or additive…

Q: What is yield strength? 2. What is tensile strength? 3. Explain Deflection of beams in terms of…

A: Yield strength and tensile strength are two important properties to consider in material selection…

Q: Using Virtual work equation, determine the angle a° so that the deflection of the point C is in the…

Q: Give me right solution with clear calculations. Use moment area method

A: Asked 1. To determine deflection at free end using moment area method

Q: Note: Show all of the diagrams used while solving the problem. Show each and every reaction and…

Q: Determine the magnitude of P such that the gap, 8, between the steel bar and the rigid horizontal…

Q: 24 m^4

Q: Derive the deflection at different points of the beam, the maximum deflection, and slopes of the…

A: Double integration method - This method is useful when the uniform bending moment equation is…

Concept explainers

Matrix Algebra for Structural analysis

Structural analysis is a process in which the effects of different loads and internal forces, acting on structures and their elements are determined. This method of analysis is effective in detecting the failure loads of the structural elements and the design can be altered before commencing the construction process, which ensures proper strength and safety of the structures.

Question

Use Conjugate Beam Method

1. The structure shown below is subjected to a total uniform load w. The flexural stress in the steel section is limited
to 150 MPa. Using conjugate beam method, determine the following:
(a) Maximum total uniform load w that can be supported by the structure
(b) Maximum shear stress,
(c) Deflection at C
(d) Slope at E.
- PL 100x10mm
w
10x130mm
PL 100x10mm
SECTION 1
B
PL 100x5mm
5x140mm
2 m
1m
1 m
1m
PL 100x5mm
SECTION 2
Section 1
Section 2
Fig. 1

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

solve step by step in digital format Solve the following exercises by the conjugate beam method A 18 ft 6 klb/ft
97. A helical spring is subjected to an axial load W and corresponding deflection in the spring is 8. Now if the mean diameter of the spring is made half of its initial diameter keeping the material, number of turns and wire cross-section same, the deflection will be
Which of the following is considered as Energy Method?I. Direct Integration Method II. Virtual Work Method III. Castigliano's Second Theorem IV. Conjugate beam Method choose in the choices
Hand written please
Write and draw the curve equation and determine the highest deflection. The material is gray cast iron. 100mm 10kN/m 40mm 120mm R, 2 m 3 m 40mm 40mm 200mm
The following may be used in getting the resultant of forces except: A Square Rule B Triangle Rule (c) Trigonometry D Parallelogram Law
sketch the deflected structure of this frame (just shape no exact values for how much deflection). This is linear analysis so only looking at the displacement of the nodes. Note that D is a hinge support, E is fixed and C is a roller
The coefficients of friction between the block and the rail are Ms = 0.25 and Mk= 0.20. Given: P2 = 600 N. Find the magnitude and direction of the smallest force P required to keep the block from moving down. The magnitude and direction of the smallest force Py required to keep the block from moving down is Note: pls show correct working out and final answer. Refer to the image and show everything in the working out like magnitude and and direction of force P1. Sorry to rush but I need this quickly!. Thanks.
Please explain all briefly or leave for someone else.
Compute the maximum deflection for the cantilever beam as shown below. Use conjugate beam method. Show complete solution and illustration.
Considering the solution above, can you help with part (d) 3. The beam shown below has a Young’s modulus of 50 GPa and has a square cross-section of side1 cm. Determine the following using the second-order integration method:(a) Bending moment M(x) along the length of the beam.(b) The slope of the beam θ(x).(c) The deflection of the beam v(x).(d) Slope of the beam at support θB
please solve using DOUBLE INTEGRATION METHOD