F1 A square rod with dimensions 0.02 m x 0.02 m x 0.5 m is attached to a solid surface as shown. If the forces on the rod are too large, it will either crush or be sheared off where it is attached to the solid surface. If the rod can withstand either a maximum normal stress of 25 kPa or a maximum shear stress is 15 kPa, a)what is the largest allowable magnitude of F, (in N) if F,=0? b)what is the largest allowable magnitude of F, (in N) if F,=0? F,

F1 A square rod with dimensions 0.02 m x 0.02 m x 0.5 m is attached to a solid surface as shown. If the forces on the rod are too large, it will either crush or be sheared off where it is attached to the solid surface. If the rod can withstand either a maximum normal stress of 25 kPa or a maximum shear stress is 15 kPa, a)what is the largest allowable magnitude of F, (in N) if F,=0? b)what is the largest allowable magnitude of F, (in N) if F,=0? F,

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the state of stresses (in MPa) shown in the figure below, the maximum shear stress (in MPa) is 2 2
A high-density polyethylene [E = 121 ksi and a = 61 x 10-6/°F] block (1) is positioned in a fixture. The block is 2.2 in. by 2.7 in. by 29 in. long. At room temperature, a gap of 0.11 in. exists between the block and the rigid support at B. Determine: (a) the normal stress o in block (1) caused by a temperature increase of 98°F. (b) the normal strain & in block (1) at the increased temperature. [ Answerrs: (a) o = (b) = 0.11 in. 29 in. Ans: (a) - 264.3725 με. (b) 3793.1033 psi.
4.20. A copper tube 55 mm in outside diameter and of wall thickness 5 mm fits loosely over a solid steel circular bar 40 mm in diameter. The two members are fastened together by two metal pins each 8 mm in diameter and passing transversely through both members, one pin being near each end of the assembly. At room temperature the assembly is stress free when the pins are in position. The temperature of the entire assembly is then raised 40°C. Calculate the average shear stress in the pins. For copper E = 90 GPa, a = 18×10 °C; for steel E200 GPa, a 12 x 10 *°C. Ans. 132 MPa
At a point in a machine component that is subjected to plane stress, the normal and shear stresses are 0 = 100MPa, oy = 35 MPa, and Txy = 70MPa, acting in the directions shown in the figure. Oy Txy Ox
The maximum principal stress for the stress state shown in the figure is (a) o (b) 20 (c) 30 6 (d) 1.50
The major and minor principal strains in a 2D stressed element are 70μ and -25µ respectively. If the normal strain at a plane is given as 15µ, then what will be the normal strain on a plane perpendicular to it? A B d C D 40μ 30μ 25μ 20μ
The rectangular plate is subjected to force P that causes elongation in the horizontal direction and shrinking in the vertical direction as shown with the dashed line in the figure. Assume a = 550 mm, Δx = 2 mm, and Δy = 1.1 mm. Determine the shear strain γxy at point A? Determine the shear strain γnt at point A? In micro rad What is the normal strain in the x-direction? What is the normal strain in the y-direction? What is the normal strain in the n-direction? Answer in clear way please
Solid Mechanics
Part B - The internal reaction at B Assume that the axial member is in equilibrium and the applied forces are an unknown load F₁. F = 5 kN. F₂ = 3 kN, and F₁ = 2 kN. Calculate the internal resultant normal force at section B. Express your answers to three significant figures in kN. ▸ View Available Hint(s) PB = Submit ΨΕ ΑΣΦΠ Part C - The internal reaction at D PD = Submit D] ΑΣΦΩΤ vec Assume that the axial member is in equilibrium and the applied forces are an unknown load F₁, F₂=5 kN. F₂ = 3 kN. and F₁ = 2 kN. Calculate the internal resultant normal force at section D. Express your answers to three significant figures in kN. ▸ View Available Hint(s) Part D - The average normal stress µA vec Value P * ? ? Units KN 2 ? Suppose the axial member has a circular cross section with a diameter of d = 16 cm at section B and a diameter of dp = 8 cm at section D. What is the average normal stress in the section with the maximum magnitude stress? Express your answer to three significant figures…
4. A uniform bar with an area of o.25 in- is pulled between two points. The tensile force at a temperature of 21.11°C is 1200 lb. What will be the stress at -17.78°C? At what temperature will the stress be zero? Assume a = 6.5 × 106 in/(in-°F) and E = 29 × 10ʻ psi. %3D %3D
The bronze bar 3.00 m long with a cross-sectional area of 350 mm is placed between two rigid walls. At a temperature of – 20 °C, there is a gap of 2.20 mm. Find the temperature at which the compressive stress in the bar will be 30 MPa. Use a = 18x10/°C and E = 80 GPa. L = 3.0 m 2.20 mm
An 18-m-long steel wire of 10-mm diameter is to be used in the manufacture of a prestressed concretebeam. It is observed that the wire stretches 55 mm when a tensile force P is applied. Knowing that E=250GPa, determine (a) the magnitude of the force P, (b) the corresponding normal stress in the wire