PROBLEM 1.3 75 mm 12AN Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Determine the magnitude of the force P for which the tensile stress in rod AB is twice the magnitude of the compressive stress in rod BC. 12AN 750mm 1000m

PROBLEM 1.3 75 mm 12AN Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Determine the magnitude of the force P for which the tensile stress in rod AB is twice the magnitude of the compressive stress in rod BC. 12AN 750mm 1000m

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in diameter and 6 bronze bolts on a concentric bplt circle 200 mm. in diameter. What are the sizes of bolts diameters for steel and bronze, if the torque applied is 6,000 N-m and without exceeding the stress of 60 MPa in the steel and 40 MPa for the bronze? The ratio of the bolt diameter db / ds = 0.50. For steel, use Gs = 83 GPa and for bronze, Gb = 28 Gpa.
PLS PROVIDE COMPLETE SOLUTION THANKS
Situation 1: A rigid bar ABC weighs 10 kN/m. The compressive stress of the copper bar is 20 MPa. Answer the following questions: 3m B 2 m Copper L=3m A = 1500 mm² Brass C L = 2 m A = 1200 mm² A. What is the stress of the brass bar? Indicate if it will experience tension (T) or compression (C) (MPa) B. What is the minimum required diameter of the pin at A assuming that the pin connection is in double shear? Consider the allowable shearing stress of the pin as 15 MPa. Round your answer in a multiple of 5. (mm)
2) A solid rod with the given dimension shown in Fig. Axial loads are applied at the positions indicated. Find the f a) The max Compressive stress in the system P-60 kN Aluminum A=400 mm b) The max Tensile stress in the system P-60 kN Steel A = 500 mm² Bronze A-200 mm² 4P 2.5 m 1.5 m 2.0 m 2P
A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in diameter and 6 bronze bolts on a concentric bolt circle 200 mm. in diameter. What are the sizes of bolts diameters for steel and bronze, if the torque applied is 6,000 N-m and without exceeding the stress of 60 MPa in the steel and 40 MPa for the bronze? The ratio of the bolt diameter db / ds = 0.50. For steel, use Gs = 83 GPa and for bronze, Gb = 28 Gpa.
The bar 1 consists of an aluminum cover and a brass core. The data is presented in the table. Determine: a. The maximum force P that can be applied at C. Answ: 84.22 kN. b. The deformation at the point where the load is applied. Answ: 1.5278 mm.
ok Strength of Materials donO نورا حياتها مترجر شریه ✓t مقادم نلود Dr. Mohammed Hashim Mohammed Problems tan't yorada grutegraat km). E1.x² (1) A steel rod with cross-sectional area of 150mm² is stretched between two fixed points. The tensile load at 20°c is 5 kN. What will be the stress at -20°c? At what temperature the stress will be zero? bedre α = 11.7x10 6/2 and E = 200x10² N/m².
Bar A was manufactured 2 mm less than bar B due to an error. The attachment of these bars to the rigid bar wouldcause a misfit of 2 mm. Calculate the initial stress in each assembly. Which of the two assembly configurationyou would recommend? Use modulus of elasticity of E = 80 GPa and diameter of the circular bars as 32 mm.
strength of material MENG222 Please solve the problem step by step and make your line clear and don't forget FBD and show me your step Please make sure your answer is correct please
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress (in Mpa) in the bronze given that P= 188 kN? Express your answer in four decimal places.
A ngid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D. as shown Neglect deflections of the bar due to bending Use E200 GPa What is the displacement of the loaded end of the bar? 2 Determine the tensile stress induced in rod CD by the 80 kN load the alowable stress in rod CD is 124 MPa, what weight W can be safely applied?
I need the answer quickly