A homogenous rod of constant cross-section carries an axial load P as shown in the figure. Initially, there is a gap of 0.5 mm between the end of the rod and the vertical wal on the right. Assuming that the walls are rigid, determine the stress on seament BC of the rod 150 KN 1.0 m 2.0 m Steel A= 600 mm?

A homogenous rod of constant cross-section carries an axial load P as shown in the figure. Initially, there is a gap of 0.5 mm between the end of the rod and the vertical wal on the right. Assuming that the walls are rigid, determine the stress on seament BC of the rod 150 KN 1.0 m 2.0 m Steel A= 600 mm?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Using an Permissible stress of 155 MPa, determine the maximum bending moment M that can be applied to the wide-flange beam shown in the figure
Since P = 10 kN in the welded annex given in the figure,a) Write the equation for the neutral axis in the cross section.b) Draw the normal stress distribution
do not shortcut please
A steel rod of 15- mm diameter is held snugly (but without any initial stresses) between rigid walls by the arrangement shown in the figure part (a). (For the steel rod, use α = 12 x 10-6/˚C and E = 200 GPa.) Calculate the temperature drop ΔT (degrees Celsius) at which the average shear stress in the 12 – mm diameter bolt becomes 45 MPa. Also, what is the normal stress in the rod? What are the average bearing stresses in the bolt and clevis at A and between the washer (dW = 20mm) and wall (t = 18 mm) at B? If the connection to the wall at B is changed to an end plate with two bolts (see figure part b), what is the required diameter db of each bolt if the temperature drop is ΔT = 38˚C and the allowable bolt stress is 90 MPa?
Find the Stress if Tensile force 2.3 N applied on rod having cross sectional area of 1 mm2
Steel Tank with an outside diameter of 600 mm has a wall thickness of 8 mm. The tank is used as storage of gas under pressure of 2.2 MPa. a. Determine the value of the tangential stress in the tank wall Determine the value of the longitudinal stress in the tank wall b. 30 mm helt hand
please answer all parts step by step and clear answer.
Question #2. The rectangular plate is subjected to the deformation shown by the dashed line. Determine the average shear strain Yxy in the plate. y -150 mm 3 mm B 200 mm A 3 mm x
2. The assembly in Figure consists of a light rigid bar AB, pinned at 0, that is attached to the steel and aluminum rods. In the position shown, bar AB is horizontal and there is a gap, A = 5 mm, between the lower end of the steel rod and its pin support at C. Compute the stress in the aluminum rod when the lower end of the steel rod is attached to its support. 0.75 m 1.5 m A B Steel A = 250 mm? E = 200 GPa Aluminum L= 2 m A = 300 mm? E = 70 GPa D
S=25
In the figure below is a slim, high-strength steel rule (E = 30X106 psi) having thickness 0.175 in. and length of 48 in. has a moment applied into a circular are subtending a central angle of 40 degrees. L = length Mo Determine the maximum bending stress (ksi). 76.4 21.3 15.3 38.2 Mo
Problem 2: A one inch diameter machined steel cantilever 10 in. long is loaded on the end with a force that varies from 60 lb down to 100 lb up. There is a "fillet where the member is connected to the support which causes a theoretical stress concentration factor K+ = 1.32. The notch sensitivity factor q may be taken at 0.92. If the material has an ultimate stress s= 80,000 psi, an endurance limit in reversed bending s= 35,000, and a yield strength, s,= 60,000, determine: (a) maximum bending stress, (b) minimum bending stress, (c) mean stress, (d) variable stress, (e) design factor N.