A secondary sedimentation tank receiving the effluent from an aeration tank has been monitored over a long time. Average values of input and output flows and suspended solids (SS) concentrations are given below. Calculate SS concentration and underflow from the bottom of the tank. The inflow of the sedimentation tank is 1000m³/d and the outflow is 600m³/d SS concentration in the influent is 3000g/m³ and SS concentration in the effluent is 30g/m³ (10)

A secondary sedimentation tank receiving the effluent from an aeration tank has been monitored over a long time. Average values of input and output flows and suspended solids (SS) concentrations are given below. Calculate SS concentration and underflow from the bottom of the tank. The inflow of the sedimentation tank is 1000m³/d and the outflow is 600m³/d SS concentration in the influent is 3000g/m³ and SS concentration in the effluent is 30g/m³ (10)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q2: A column analysis for an activated sludge suspension yielded the following: MLSS Conc (mg/l) Settling velocity m/h 1000 2.8 2000 3000 1.2 0.4 4000 0.2 5000 Question 0.1 6000 0.06 The influent MLSS concentration is 2000 mg/l and the flow rate is 4200 m³/d. Determine the size of the clarifier that will thicken the solids to 8000 mg/l.
A rectangular sedimentation tank following coagulation- Exa flocculation is to treat a flow of 3000 m³ / day with a detention time of 6 hours. It is to be hand cleaned of sludge at 6 week intervals. The suspended solids concentration of the water is reduced from 250 mg/L to 5 mg|L by coagulation- flocculation. The settled sludge includes 40 mg/L (based on water flow) of metallic precipitate and has a moisture content of 85% and specific gravity of 1.24. Determine the volume of sludge produced between cleanings and the basic dimensions of the tank if the water depth just before cleaning is 3 m and its length is twice its width.
2. (a) Design a gravity thickener to concentrate the mixture of sludge obtained from primary and secondary settling units in an activated sludge wastewater treatment plant. Make appropriate assumptions in your calculations. Sludge waste flow rate in the primary settling unit= 140 m³/d; and concentration = 2.5% Sludge waste flow rate in the secondary settling unit= 350 m/d; and concentration = 0.6% Qi ci Solids Loading Rate (SLR) = 40 kg ds / m².d, and SLR : A ci Qi Tc Expression for thickening zone depth= 0.75Cu A Ci: Incoming mixed sludge concentration Qi: Incoming mixed sludge flow rate A: Cross section area of the thickening tank Cu: Target underflow concentration (=5%) Tc: Time in compression zone (=2 days)
Water treatment plant : SOR = 0.35 mm/sec; The analysis of this water found that there are 6 different particle sizes: 0.1 mm with settling velocity of 0.2 mm/sec; and percentage of particles = 10 %; 0.2 mm with settling velocity of 0.25 mm/sec; and percentage of particles = 20 %; 0.3 mm with settling velocity of 0.3 mm/sec; and percentage of particles = 15 %; 0.4 mm with settling velocity of 0.35 mm/sec; and percentage of particles = 5 %; 0.5 mm with settling velocity of 0.4 mm/sec; and percentage of particles = 30 %; 0.6 mm with settling velocity of 0.5 mm/sec; and percentage of particles = 20 %; Calculate the efficiency of this tank ?
Question # 3 (a): Design a sedimentation tank used for a surface overflow rate of 16.0 m/day to treat a flow of 625 m3/hr. having detention time of 120 minutes. Provide a storage sludge capacity of 20 % of effective volume. Under ideal condition what size of particles will be removed 100% if specific gravity is 2.65, μ = 1* 10-3 kg/sec-m and density of water is 1000 kg/m3. Subject: Environmental Engineering
Downvote for incorrect solution..A domestic wastewater contains 350 mg/L of suspended solids. Primary sedimentation facilities remove 65%. Approximately how many cubic meters of sludge containing 5% solids will be produced per million cubic meters of wastewater settled?
C. What is the concentration UI SUINUS 5. Determine the size (diameter and depth) of the secondary clarifier (s) at a municipal activated sludge treatment facility: The wastewater flow is 25,000 m³/d, the recycle ratio (recycle sludge flow/wastewater flow) is 0.25. The suspended solids concentration is assumed to be 2500 mg/L in the activated sludge tank. The over flow rate is 50 m3/d- m2 and solids loading is 125 kg/d-m2. Estimate detention time if the depth is 4.5 m. What would be the weir loading? Department of Civil & Environmental Engineering P.O. Box 519 Mail Stop 2510, Prairie View, Texas 77446 w.pvamu.edu Phone (936) 261-1660/1665(dept) Fax (936) 261 1662 Ensuring o Using Zoom o
Determine the area required for solids thickening in a clarifier receiving 1,500 m³/s of influent with a solids concentration of 800 mg/Lif the underflow concentration 12,000 mg/L. The settling flux curve for the sludge is provided below. Also determine the limiting flux JL, the limiting solids concentration CL, and the underflow rate Qu. Solids flux, kg/m²-h 12 10 8 6 4 2 0 0 5 BAT 10 Solids concentration, kg/m³ = g/L 15
Silt-containing wastewater flowing at a rate of 24.2x103 m3/day was fed to a sedimentation tank with dimensions L= 39 m, W= 8m, H=3m The SG of the particles is 2.68. What would be the smallest particle size (in µm) that can be removed from this operation? Assume flow is within Stokes region and that the particles are spherical. The density and viscosity of water is 1000 kg/m3 and 0.001 kg/m-s, respectively.
A completely mixed activated sludge process operating at equilibrium is designed to treat 300 MLD of waste water. The influent and effluent BOD are 200 mg/1 and 18 mg/1 respectively If the F M then the hydraulic retention time is A 0.125 day B 4.21 hours C 8.42 hours D 0.225 day = 0.3 and MLSS is 3800 mg/1,
Ex: Design a digestion tank for the primary sludge with the help of following data : (i) Average flow = 20 Mld ; (ii) Total suspended solids in raw sewage (iii) Moisture content of digested sludge = 85%. Assume any other suitable data you require. %3D 300 mgll ; %3D
A sedimentation basin in a water treatment plant treats a flow of 6 mgd and has the following dimensions: L= 120'; W = 12'; D = 12’. Water is being treated at an average temperature of 3. 20°C. Calculate the water detention time (in hours and minutes), horizontal velocity (in ft/min), and overflow rate (in gpd/ft², gpm/ft² and ft’/ft²-day). b. If a particle is to be 100% removed and has a specific gravity of 2.5, what is the corresponding particle diameter (in mm)? Is Stoke's Law appropriate for this situation? Why or why not? а.