Compute the adjusted length of inie AC

Q: Locate the centroid y of the shaded ared. L=23.6mm y 2L L 2L 2L

A:

Q: Find force P required for the given situation: 350 Nfa 一+ 20mm O 625 kN O 525 kN O 550 kN O 600kN

A: We will multiply shear stress to shear area to find load.

Q: 12. Determine the resultant couple moment acting on the triangle plate *

A:

Q: f=122 mm hf=30mm hw=40mm bw=30mm Moment =95 N.

A: M=95 Nm

Q: find the stresses on the plane 45 Draw

A:

Q: HW #3 Sbom e:0,3mm レ=300m Find D usiug covel Brook Dンて without e9nivalent Lenght Slom

A:

Q: Complete the following differential level notes for a double-rodded line from BM1 to BM2. Show the…

A: Complete the following differential level notes

Q: Calculate the polar radius of gyration of the shaded area about its centroid C. Assume t=115 mm, a…

A:

Q: In the figure, suppose the length L of the uniform bar is 3.0 m and its weight is 190 N. Also, let…

A: To solve this problem  the equilibrium equations will be used.

Q: 2 ft Determine th of the centra 4 ft

A:

Q: Problem 6.23 (Ans. 9.93 mm) Wp = 12 kN/m WL 16 kN/m 480 mm 550 mm 4 #22 -6 m- 300 mm 70 mm

A: There are few data Missing in the question. In order to get the given answer 9.93 mm I have the…

Q: Q2:- A rectangular gate AB in Fig is I m long and 1.Sm wide into the paper, hinged at 4, and resting…

A: formula to find force exerted on flat plates immersed in the water F=γAhγ= unit weight of liquidA=…

Q: DETERMINE THE FOLLOWING; A. CENTROID OF THE CROSS-SECTION B. SECOND MOMENT OF AREA OF THE STRONGER…

A: A Section of structure member is given belowNeed to find1- Centroid of the section2- second moment…

Q: Civen that the tension in segment AB 130 N WITH a rathio of 1H: 2v, which of the fo llowing nearly…

A:

Q: A flanged wooden shape is used to support the loads shown. The dimensions of the shape are shown.…

A: Introduction- The maximal compressive stress and tensile stress on a beam under bending moment…

Q: 1. Using the conjugate beam method, determine the slope and deflection at point B of the beam ABC…

A:

Q: 3- Long column braced against side movement means Non-sway frame : а- Yes b- No 4- What is the…

A:

Q: 7.59 7% 0.750 1.15 1% % Compute the moment of inertia for the built up section shown below about the…

A:

Q: The 560-kg uniform I-beam supports the load shown. Determine the reactions at the supports. Answers:…

A: Given data,  Total length of I beam = 8 m Weight of beam = 560 kg Point load at 5 m frim left…

Q: QeAFin d The (fEM) a wi (6 12

A:

Q: Figura P2.43 75 mm 100 mm 1 8 in 10 in 2.44 La barra rígida AD está soportada por dos alambres de…

A: D = 116 in E = 29 x 106 psi  P = 220 lb

Q: A flanged wooden shape is used to support the loads shown. The dimensions of the shape are shown.…

A: Given data;

Q: Draw the state of stress at point D on an infinite small element. Point D is located just to the…

A: Given :- By using the method of section and consider the FBD of the left cut segment.

Q: Please answer nos. 16 and 17 N=82 M=132 L=102

A: Given data  N = 82, M = 132, L = 102  Fu = 400 MPa   Net to find question number -16

Q: Determine the force of all members using METHOD OF JOINT. Answer in 3 decimal places only. TRUSS…

A: Objective: To determine the force of all members of the given truss using the method of joints.…

Q: 5. Find the Total efongation of the bar below 12KN 6KN 4KN 4KN+ 6KN L1 12 L3 L4

A:

Q: Open notes, use f. 28 MPa, f,=420 MPa everywhere, except otherwise noted. Determine the design…

A:

Q: Determine the force-couple system acting at point 0. 50 N 90 N 40° В 40 N m 400 mm 1300 mm A 4 800…

A:

Q: Use superposition merhod

A: Given Data E = 29 × 103 ksi  I = 500 in.4  Support B downward settlement (∆B) = 0.25 ft  Determine…

Q: Byusing ConjugateBeamMethod, Determinethedeflection 3mtotheleft of rollersupport 55 kN 30 kN/m B A C…

A:

Q: For the frame shown ba louw use unil. load melhed to defermin vertical def lection at c 2 atc2 E=200…

A: We have to find vertical deflection at C

Q: 8. Using cut a-a, get CD and JK forces. 3 kips 3 kips 3 kips 3 kips 4.5 ft B FO 4.5 ft C 4.5 ft G D…

A:

Q: • Two forces act on the hook. Determine the magnitude of the resultant force 30 200 N 40 500 N

A:

Q: Correction for Problem Set Problem 11 A base line was measured in catenary as shown below, with a…

A:

Q: Problem Statement A site selected for construction of multistorey building has a layered stratum as…

A:

Q: For a highway curve with R= 1000 m, I = 16°30', and Pl station = 3 +264.759 m, calculate the…

A: Radius of curve R = 1000 m = 1000 × 3.28084 = 3280.84 ftI = 16 °30, = 16.5°PI = 3+264.759

Q: c. What is the over-consolidation ratio of the clay layer in the new soil profile. 3. How much is…

A:

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.