In the figure, suppose the length L of the uniform bar is 3.0 m and its weight is 190 N. Also, let the block's weight W = 280 N and the angle 0 = 31°. The wire can withstand a maximum tension of 450 N. (a) What is the maximum possible distance x before the wire %3D breaks? With the block placed at this maximum x, what are the (b) horizontal and (c) vertical components of the force on the bar from the hinge at A? C com A

In the figure, suppose the length L of the uniform bar is 3.0 m and its weight is 190 N. Also, let the block's weight W = 280 N and the angle 0 = 31°. The wire can withstand a maximum tension of 450 N. (a) What is the maximum possible distance x before the wire %3D breaks? With the block placed at this maximum x, what are the (b) horizontal and (c) vertical components of the force on the bar from the hinge at A? C com A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2) will upvote anyone who will answer.
Problem- A mild steel bar of length 450 mm tapers uniformly. The diameters at the ends are 36 mm and 18 mm, respectively. An axial load of 12kN is applied on the bar. E= 2 × 10 N/mm². The elongation of the bar will be
Q2: Find the permissible distance (X) for the beam shown in figure. If the stresses in tension is 40 MPa and in compresion is 80 MPa. 4kN 4KN. 220 16KN N. A 大 6m 'RB INA: 4 = 20* (o mm
I want the correct solution with proper explanation.
Q 3. A rigid beam AB is 5.5 m long, hinged at point A and supported by two pipes at C and D as shown in figure 3 below. Pipe 1 at C is of copper has a outer diameter of 120 mm and inner diameter of 100 mm and yield stress of copper is 138 N/mm² Pipe 2 at D is of steel has a outer diameter of 100 mm and inner diameter of 90 mm and yield stress of steel is 250 N/mm2 Calculate the safe load at A if the load factor is 1.66 Pipe 1 Pipe 2 Psafe 2.3 m 2 m C 5.5 m Angle ACE = 0 Figure 3 Angle BDF = 42° Take 0 = 10 Page 7 of 7 PTO
Determine the magnitude of the pin force at A. Assume W = 520 Ib, a = 2.9 ft, b = 2.4 ft, r = 7 in. a C B A W D Answer: A = i Ib
Calculate the moment of Resistance of the given beams. If the maximum stress is 100 N/mm2. 190 |不 15 (i) 550 k10> (all dimensions in mm)
Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Determine the magnitude of the force P (in lb) for which the tensile stress in rod AB is thrice the magnitude of the compressive stress in rod BC if Q = 20.11 lb.
5. A part of robotic link is shown below and links are designed with yoke. Two links are joined by a Hinge pin and each side is supporting a load of P = 14 kips. Consider that the shearing stress of the pin is 12 ksi and bearing stress is 20 ksi, find the diameter of the pin and the minimum thickness of the link's yoke.
Design the diameter of the pin for the hinge support if the allowable shear stress is 250 MPa. *DRAW THE FREE BODY DIAGRAM *COMPLETE SOLUTION *3 decimal places ALL ANSWER
Choose the letter of the correct answer. Show complete solution if possible.