A completely mixed activated sludge process operating at equilibrium is designed to treat 300 MLD of waste water. The influent and effluent BOD are 200 mg/1 and 18 mg/1 respectively If the F =0.3 and MLSS is 3800 mg/1, M then the hydraulic retention time is A 0.125 day B 4.21 hours C 8.42 hours

A completely mixed activated sludge process operating at equilibrium is designed to treat 300 MLD of waste water. The influent and effluent BOD are 200 mg/1 and 18 mg/1 respectively If the F =0.3 and MLSS is 3800 mg/1, M then the hydraulic retention time is A 0.125 day B 4.21 hours C 8.42 hours

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4. I 1 I (mm/hr) = at + 12 where it is accumlated in filtration time (min) use the below Data to estimate Dein fretration rate. after (one) hour. N'ary wiI) (t) min lime (D) Accumlation infiltratim : depth (mm) 30 Yo 150 80 - talles
Water treatment plant : SOR = 0.35 mm/sec; The analysis of this water found that there are 6 different particle sizes: 0.1 mm with settling velocity of 0.2 mm/sec; and percentage of particles = 10 %; 0.2 mm with settling velocity of 0.25 mm/sec; and percentage of particles = 20 %; 0.3 mm with settling velocity of 0.3 mm/sec; and percentage of particles = 15 %; 0.4 mm with settling velocity of 0.35 mm/sec; and percentage of particles = 5 %; 0.5 mm with settling velocity of 0.4 mm/sec; and percentage of particles = 30 %; 0.6 mm with settling velocity of 0.5 mm/sec; and percentage of particles = 20 %; Calculate the efficiency of this tank ?
Settling tank has a depth of 3 m and surface area of 900 m2 is used to remove particles of size 0.01 mm and specific gravity 2.65. Compute the removal percentage of the tank for the discharge of 8000 m3/d. Take viscosity of water equal to 10-3 kg/m.s.
Q1: The design flow for a water treatment plant (WTP) is 1 MGD (3.8x10 m³ /d). The rapid mixing tank will have a mechanical mixer and the average alum dosage will be 30 mg/L. The theoretical mean hydraulic detention time of the tank will be 1 minute. Determine the following: a) the quantity of alum needed on a daily basis in kg/d, b) the dimensions of the tank in meters for a tank with equal length, width, and depth, c) the power input required for a G of 900 sec' for a water temperature of 10 °C. Express the answer in kW, given that u = 1.307 × 10³Kg/m.s.
Please give me both a and b solutions A settling tank with (L=6m, W=4 m , H= 4 m) treats a waste stream (60,000 l/min) and removes suspended solids with 200 micrometer diameter that have a settling velocity of 0.04 m/s. a. What is the removal efficiency of his tank? b. If a 100% removal efficiency is to be achieved, How long should the settling tank be?
Complete solution Civil engineering
Plz write neat
Calculate the minimum fluidization velocity for an anthracite bed having following characteristics; d90 = 2.9 mm, ?anthracite = 1600 kg/m3, ?water = 998 kg/m3 at 20°C; µ = 1.002x 10-3 kg/m.sec
1. The following information is provided for an activated sludge system design: Parameter Symbol Value Units Flow rate Q 10000 m³/d Influent BOD So 150 mg/L Effluent BOD S 2 mg/L Hydraulic residence time Ꮎ 4 hr Mean cell residence time Oc 6 d Maximum specific growth rate μm 3 1/d Half saturation constant Ks 40 mg/L Yield coefficient Y 0.5 Endogenous decay coefficient b 0.08 1/d Death rate coefficient γ 0.04 1/d Determine: a) The aeration tank biomass concentration (X) in mg/L b) The aeration tank oxygen requirement in kg/d c) The rate of biomass wasting in kg/d
Gave wrong values earlier. These are the correct values A settling tank having a depth of 3.5 m and surface area of 1000 m2 is used to remove particles of size 0.01 mm and specific gravity of 2.6. Calculate the removal percentage of the tank for the discharge of 7000 m3/d. Take viscosity of water as 1.1x10-3 kg/m.s.
A complete-mixed activated sludge process (CMAS) is to be designed to treat 6.0 MGD of primary effluent having a BOD5 of 190 mg/L. The requirement is that the effluent BOD5 and TSS concentrations be 20 mg/L or less on an annual average basis. The following biokinetic coefficient obtained at 15°C: Y = 0.6 mg VSS/mg BOD5, k = 2.85 d-1, Ks = 70 mg/L BOD5, and kd = 0.041 d-1. Assume that the MLVSS concentration in the aeration basin is maintained at 2,500 mg/L. Determine: a. The minimum MCRT (d) b. The MCRT necessary to meet the requirement (d) c. The volume of the aeration basin (ft3)
A rectangular settling basin has a depth of 3 m, a length of 40 m and a width of 6 m. The water treated in the basin has a flow rate of 500 L/s and contains 50 mg/L of type a particles, 100 mg/L of type b particles and 180 mg/L of type c particles (particle type letters refer to the particles listed in problem 1). What is the suspended solids concentration in the effluent from the settling basin? Determine the overall percent removal of suspended solids from the water achieved by the settling basin.