A pipe carrying steam at 3.5 MPa has an outside diameter of 450 mm and a wall thickness of 10 mm. A gasket is inserted between the flange at one end of the pipe and a flat plate used to cap the end. How many 47-mm-diameter bolts must be used to hold the cap on if the allowable stress in the bolts is 80 MPa, of which 55 MPa is the initial stress?

A pipe carrying steam at 3.5 MPa has an outside diameter of 450 mm and a wall thickness of 10 mm. A gasket is inserted between the flange at one end of the pipe and a flat plate used to cap the end. How many 47-mm-diameter bolts must be used to hold the cap on if the allowable stress in the bolts is 80 MPa, of which 55 MPa is the initial stress?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.1P: A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the...

See similar textbooks

Similar questions

A pipe carrying steam at 3.5 MPa has an outside diameter of 450 mm and a wall thickness of 10 mm. A gasket is inserted between the flange at one end of the pipe and a flat plate used to cap the end. How many 40-mm-diameter bolts must be used to hold the cap on if the allowable stress in the bolts is 105 MPa, of which 55 MPa is the initial stress? What circumferential stress is developed in the pipe? Why is it necessary to tighten the bolt initially, and what will happen if the steam pressure should cause the stress in the bolts to be twice the value of the initial stress? *
A boiler with an outside diameter of 300 mm, length of 1000 mm and a wall thickness of 10 mm is carrying steam at 4.5 MPa. A seal is inserted between the flange at one end of the boiler and a flat plate is used to cap the end. Determine the following: How many 40-mm-diameter bolts must be used to hold the cap on if the allowable stress 3.1 in the bolts is 80 MPa, of which 50 MPa is the initial stress? 3.2 What circumferential stress is developed in the boiler? 3.
A pipe carrying steam at 3.0 MPa has an outside diameter of 450 mm and a wall thickness of 10 mm. A gasket is inserted between the flange at one end of the pipe and a flat plate used to cap the end. How many 25 mm diameter bolts must be used to hold the cap on if the allowable stress in the bolts is 90 MPa of which 50 MPa is the initial stress? What circumferential stress is developed in the pipe?
6. A PIPE CARRY|NG STE AM AT 3.5 MPa HAS AN OUTSIDE DIAMETER OF 450 mm AND A WALL THICKNESS OF 10 mm. A GASKET IS INSERTED BETWEEN THE FLANGE AT ONE END OF THE PIPE AND A FLAT PLATE USED TO CAP THE END. HOW MANY 40 mm- DIAMETER BOLTS MUST BE USED TO HOLD THE CAP ON IF THE ALLOWABLE STRESS IN THE BOLTS IS 105 MPa, OF WHICH 55 MPa IS THE INITIAL STRESS ? WNHAT CIRCUMFERENTIAL IN THE PIPE ? TO TIGHTEN THE BOLT INITIALLY, AND WHAT WILL STRESS IS DEVELOP WHY IS IT NECE SSARY HAPPEN IF THE STEAM PRESSURE SHOULD CAUSE THE STRESS IN THE BOLTS TO BE TWICE THE VALUE OF THE INITIAL STRESS?
PROBLEM 3. A double-row butt joint is used as a connection. It is made up of two 210-mm by 20-mm cover plates and 210-mm by 35-mm main plate. The plates are to be connected by 32-mm diameter rivets. The allowable stresses are 75MPa for shear, 90MPa for tension and 285MPa bearing. Assume that each hole is 3mm larger than the rivet diameter. ust PDF ng imen GIBL o Alel 1. What is the largest value of P (kN) that can be applied without exceeding the ollowable stress for shear? 2. What is the largest value of P (kN) that can be applied without exceeding the ollowable stress for bearing? 3. What is the largest value of P (kN) that can be applied withour exceeding the allowable stress for tension? ng in
How many 10-mm diameter rivets is needed to fasten member BF to the gusset plate at B if the member BF has thickness of 8 mm and the working stresses are 30 MPa for shear in the rivets and 45 MPa for bearing due to the rivets.
The tank shown in the figure shown is fabricated from a steel plate. a. Determine the maximum longitudinal stress caused by an internal pressure of 1.2MPA if the steel plate has a thickness of 10mm. b. Determine the maximum circumferential stress caused by an internal pressure of 1.2MPA, if the stress plate has a thickness of 10mm. c. Determine the minimum thickness plate which maybe used if the stress is limited to 40MPA and the internal pressure is 1.5MPA. 1400 mm 400 mm 600 mm
Question 2
1. A 60-mm diameter steel tube with a wall thickness of 3 mm just fits in a rigid hole. Determine the tangential stress developed if an axial compressive load of 12 kN is applied. Use v = 0.30 and E = 200 GPa. Answer: 0 = 6.37 MPa 2. A 200-mm long bronze tube closed at both ends fits without clearance in a 70-mm hole in a rigid block. It has a diameter of 70 mm and a wall thickness of 5 mm. The tube then sustained an internal pressure of 4.5 MPa. Use v = 0.33 and E= 83 GPa. Compute the tangential stress in the tube. Answer: Ot = 5.20 MPa
For the pin connection shown, determine the normal stress acting on the gross area, the normal stress acting on the net area, the shear stress in the pin, and the bearing stress in the steel plate at the pin.
A spherical gas tank is fabricated by bolting together two thin-walled hemispherical shells with an inner diameter of 8 m. The gas is pressurized to 2.0 MPa. The shells have an allowable normal stress of 150 MPa, and the 25 mm-diameter bolts have an allowable normal stress of 250 MPa. (a) Determine the minimum thickness of the walls of the tank to the nearest mm. (b) Determine the minimum number of bolts to connect the hemispheres.
Question 24 A 3 m long hollow circular tube made from aluminium with an outside diameter 200 mm and a wall thickness of 10 mm is filled with a polymer matrix. It is subjected to a tensile axial force of 500 kN acting uniformly over the entire cross-sectional area of the filled tube. If the elastic modulus of the aluminium is E₂=75 GPa, and of the matrix is Em 15 GPa, calculate the normal direct tensile stresses acting on the two materials and the extension of the tube. = Which of the following answers is correct? The tensile stress in the aluminium is ten times larger than the tensile stress in the matrix The tensile stress in the aluminium is 45.2 MPa and the extension of the tube is 1.8 mm. The tensile stress in the matrix is 19.1 MPa and the extension of the tube is 3.1 mm. O The tensile stress in the matrix is 40.5 MPa and the extension of the tube is 2.5 mm. AMSUN The tensile stress in the aluminium is 54.7 MPa and the extension of the tube is 0.8 mm.