The rectangular bar is connected to the support bracket with a 24-mm-diameter pin. The bar width is w-85 mm and the bar thickness is 20 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 120 MPa, the bearing stress in the bar cannot exceed 140 MPa, and the bearing stress in the bracket cannot exceed 130 MPa. Determine the maximum value of Pmax that can be supported by the structure. Answer: Pmax KN

The rectangular bar is connected to the support bracket with a 24-mm-diameter pin. The bar width is w-85 mm and the bar thickness is 20 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 120 MPa, the bearing stress in the bar cannot exceed 140 MPa, and the bearing stress in the bracket cannot exceed 130 MPa. Determine the maximum value of Pmax that can be supported by the structure. Answer: Pmax KN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the maximum normal stress developed in the bar when it is subjected to a tension of P = 4.3 kN given t=5 mm, a=5.5 mm, b=5 mm, F0.5 mm, and D=2.2 mm. [note: Drawing is not to scale] P O 275.20 MPa O 734.26 MPa O 172.00 MPa O 1915.45 MPa O 716.67 MPa O638.48 MPa O573.33 MPa O 677.58 MPa
Pleaase answer this question ASAP! Thanks!
I need it handwritten and correct or skip please only handwritten handwritten handwritten handwritten otherwise dislikfor sure
Consider tow circular rods with a 50mm diameter are joined by a knuckle joint by a pin of 40mm in diameter. If a tensional force of 120kN are applied at each end of the rods, Determine the allowable tensile stress in the circular rods and the Average shear stress occurs in the pin.
A pulley is supported by a circular pin at A. The pin has a diameter of d = 0.375 in., and each side of the pulley support bracket has a thickness of t = 0.2500 in. The average shear stress in the pin cannot exceed 35 ksi, and the bearing stress in the pulley support bracket cannot exceed 70 ksi. Determine the maximum value of Pmax that can be supported by the assembly.
The lap joint is fastened with four 0.75-in.-diameter rivets. The working stress is 15.77 ksi for the rivets in shear. Find the maximum tensile stress (in psi) on the plates. Assume that the load is equally distributed among the rivets and w = 4.21.
3. The aluminum block has the rectangular cross-section and is subjected to an axial compressive force of 8 kips. The 1.5-in side changed its length to 1.50014 inches. Use E = 10 x 10³ ksi. Calculate the new length of the 2-inch side. Answer: Lnew = 2.00019 in 1.5 in 2 in. 8 kip- 8 kip 3 in. 4. A solid cylinder of diameter D is subjected to an axial load P. Show that its change in diameter is 8D = 4Pv/лDE.
A thin cylinder of inner radius 500 mm and thickness 10 mm subjected to an internal pressure of 5 MPa. The average circumferential (hoop) stress in MPa is
Calculate the stress perpendicular to the inclined plane AB. Report your answer as a positive number.Answer: σn= Enter your answer in accordance to the question statement ksi.
The 10-mm-diameter steel bolt in (Figure 1) is surrounded by a bronze sleeve . The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. Est = 200 GPa, Epr 100 GPa. Part A If the bolt is subjected to a compressive force of P = 15.7 kN, determine the average normal stress in the steel. Express your answer to three significant figures and include appropriate units. Ost = Value MPа Submit Request Answer Part B If the bolt is subjected to a compressive force of P = 15.7 kN, determine the average normal stress in the bronze. Express your answer to three significant figures and include appropriate units. Figure HA P Obr = Value MPа Submit Request Answer 10 mm Provide Feedback 20 mm P
The circular column is subjected to a compressive force of 5kN if the stress in the column is limitedto 17.63MPa, what is the limiting value of diameter d?
PLEASE ANSWER IT CORRECT I WILL UPVOTE AFTER