The boom AB is made up of a hollow square 80-mm tube having a wall thickness of 2 mm. A 20-mm diameter steel cable BC and a 16-mm diameter pin at A support the boom in the position shown. The working stresses are 140 MPa for the cable, 110 MPa for the boom, and 70 MPa for shear in the pin. Neglecting the weight of the boom, determine the largest safe load W that can be applied as shown. ВOOM AB -16-mm diam. 4 m pin DETAIL OF JOINT A VIEWED FROM BOTTOM 30° ww 08

Q: A hollow iron pipe with outside diameter of 240 mm is used as a column to carry a load of 80 kN.…

A:

Q: The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 10 mm2.…

A:

Q: Two holes have been drilled through a long steel bar that is subjected to a centric axial load as…

A: The maximum stress occurs to the cross-section with the minimum area. (a) The minimum…

Q: The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 7 mm2.…

A:

Q: 1. The bars of the pin-connected frame are each 300 x GOo mm in section. Determine the maximum bad P…

A: Given, A truss structure .  Area of the bar , A =300*600 mm = 0.18 m2. Maximum tensile stress ,…

Q: A flanged bolt coupling consists of eight 10-mm diameter steel bolts on a bolt circle 400 mm in…

A: Given:no=8do=10 mmDo=400 mmni=6di=10 mmDi=300 mmFo=8000 N

Q: The Bars of the Pin-connected frame as shown are each 30mm and 60mm in section. Determine the…

A: Given:   σT=100 MPaσC=80 MPaSection=60 mm×30 mm The free-body diagram of the frame considering…

Q: The boom AB is made up of a hollow square 100-mm tube having a wall thickness of 5 mm. A 10-mm…

A: Given data, Outer dimension of hollow boom AB is 100 mm and thickness is 5 mm. So, cross-sectional…

Q: A timber column, 8 in. by 8 in. in cross section, is reinforced on all four sides by steel plates,…

A: In the given problem four steel plates of width 8 inches and 't' thickness have been provided to…

Q: The lap joint shown is connected by 6 pieces rivets. Assuming that the load P = 70 KN is carried…

A: Given Data Applied load is: P=70 kN=70000 N. Number of rivets are: n=6 Allowable shear stress is:…

Q: A lightweight lever consists of a 0.8m solid bar rigidly mounted to a large structure and a 0.5m…

A: given; length from a-a cross section,(l1)=0.8mlength from tip to load…

Q: For the clevis connection shown, the shear stress in the 5/16-in.-diameter bolt must be limited to…

A: To Find : The maximum load P. Given :  The shear stress is τ=20 ksi. The diameter is d=516 in. FBD:…

Q: For the frame shown, a 4226-N load is acting on member ABD at D. If the allowable material shear…

A: The free-body diagram of the membr ECD is shown below.   Equilibrium of forces on point, E ∑Fx = 0…

Q: The 1.4-kip load P is supported by two wooden members of uniform cross section that are joined by…

A: Given Data: The load on member is P = 1.4 kip. The cross-section area is A = 3 in ×5 in. The angle…

Q: Given the assembly shown is a cylinder rod position vertically and is supported by a collar and a…

A: Shear failure between collar and cylinder: Area of shear occurs between collar and cylinder…

Q: Determine the largest weight W in kN that can be supported by the two wires AB and AC: The working…

A:

Q: 1.What is the largest value of P (kN) that can be applied without exceeding the ollowable stress for…

A: Given : Rivet dia =  32 mm hole dia = 32+ 3 = 35 mm Allowable stress for shear = 75 mpa Allowable…

Q: For the clevis connection shown, the shear stress in the 5/16-in.-diameter bolt must be limited to…

A: Given data: d=516 inτ=32 ksi Need to determine the maximum allowable load that can apply.

Q: The lap joint shown is connected by three 16-mm diameter rivets. If the allowable stress for shear…

A:

Q: 1.55 The lap joint is fastened with four 3/4-in-diameter rivets. The working stresses are 14 ksi for…

A:

Q: The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 10 mm2.…

A:

Q: For the frame shown, a 4998-N load is acting on member ABD at D. If the allowable material shear…

A:

Q: A 50-kN force is subjected to a lap joint fastened by three 20-mm diameter rivets. (a) the shearing…

A: A rivet is a short cylindrical bar with inyregral to it.the cylindrical part of the rivet is called…

Q: A 150mm x 30mm x 250mm central wooden block is glued between cantilevered brackets 200mm x 50mm each…

A: Stress Stress is defined as the ratio of force to the area on which force is acting.   There are…

Q: Two ropes are used to hoist a 530 lb engine/transmission assembly as shown. The rope is anchored at…

A: Since you have posted question with multiple sub-parts (a), (b), (c), (d), and (e), we solve first…

Q: For the clevis connection shown, determine the shear stress in the 18-mm-diameter bolt for an…

A:

Q: A 10-mm diameter steel bolt is surrounded by bronze sleeve. The outer diameter of the bronze sleeve…

A:

Q: The following bar has a diameter of 40 mm and is subjected to the loads shown. For the point A…

A: Given data :-Torque (T) = 45 NmDiameter of bar (d) = 40 mmShear load = 5 kN Distance between Share…

Q: 3. A cast-iron tube is used to support a compressive load, knowing that the maximum allowable change…

A:

Q: All members of the truss shown have a cross-sectional area of 500mm2 and all pins have a diameter of…

A:

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.