The boom AB is made up of a hollow square 100-mm tube having a wall thickness of 5 mm. A 10-mm diameter steel cable BC and a 16-mm diameter pin at A support the boom in the position shown. The working stresses are 170 MPa for the cable, 124 MPa for the boom, and 94 MPa for shear in the pin. Neglecting the weight of the boom, determine the largest safe load W that can be applied as

Q: What is the average normal stress at section b-b? 546.1 kPa

A:

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional…

A:

Q: (a) If the rope is subjected to a vertical force of P = 500 N, determine the normal stress at points…

A: Diameter of the wooden post - 40 mm = 0.04 mVertical force, P =500 N

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional…

A:

Q: o solid cylindrical rod= C are welded together d as shown. The force Determine the average at the…

A:

Q: 8.13 Determine the load carrying capacity of a hook of rectangular cross-section. The thickness of…

A: Givent=75mmRi=150mmRo=250mml=75mmσall=70MN/m2=70 N/mm2 '

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional…

A: According to the given dataa=2.75ftb=3.3ft A=2.3in2We need to findMaximum allowable load P if normal…

Q: Determine the maximum load P than can be applied on the truss at point D if the allowable stresses…

A:

Q: Determine how many 11mm bolts should be used to attach a cap to a cylindrical tank with a diameter…

A:

Q: 1-What is the average normal stress at section b-b? 546.1 kPa 267.7 kPa 813.8 kPa 779.9 kPa 942.8…

A: Given, W=200 N/m θ=550 The cross-section (square) of AB, a=1.5 cm=0.015 m The diameter of the pin at…

Q: 3. The rigid bar ABCD of negligible weight is initially horizontal, and the steel rods attached at A…

A: Given Data The load applied at D is: P=20 kips The coefficient of thermal expansion is:…

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional…

A:

Q: Two cylindrical cross-section rods AB and BC, which are fixed to the wall and welded together at…

A:

Q: Two forkend pieces are to be joined together by a single steel pin of 25mm diameter and they are…

A: Shear force is an internal force induced by an applied force, and shear diagrams for all sections of…

Q: A 20 mm diameter steel rod passes concentrically through a bronze tube (200+SN) mm long, 50 mm…

A: According to the given information  the diameter  of the steel rod is  Ds is 20 mm, the inner…

Q: A 1000 kg homogenous bar 2 m long is suspended horizontally from  two vertical cables A and B each…

A: Given Datam=1000kgA=400m2σA=100MPaσB=50MPa I had Given Required figure

Q: A bar with an allowable tensile stress of 16 ksi has two holes at A and B. Determine the maximum…

A:

Q: Two members of uniform cross section 65 x 95 mm are glued together along Plane a-a that forms an…

A:

Q: Q2/ The assembly consists of two sections of cast-iron rod connected together using a reducing…

A: Given data :- for section AB L = 12 in , d = 0.75 in for section BC L = 15 in , d = 1 in shear…

Q: The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 9 mm².…

A:

Q: Two portions of member AB are glued together along a plane forming an angle with the horizontal. The…

A:

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional…

A:

Q: In the mechanism shown below, the distributed load W is 300 N/m and the angle 0 is 35°, knowing that…

A:

Q: : Pmax i kips

A: Given: A=2.3 in2 a=3 ft b=3.6 ft normal stress= 40 ksi To determine: maximum force that can be…

Q: ternal diameter 20 mm. The tube is closed at each end with the help of rigid washers (of negligible…

A:

Q: A lightweight lever consists of a 0.8m solid bar rigidly mounted to a large structure and a 0.5m…

A: given; length from a-a cross section,(l1)=0.8mlength from tip to load…

Q: ! Required information Two horizontal 5.5-kip forces (P) are applied to pin B of the assembly shown.…

A:

Q: b. A draw bar between a tractor and a trailer is made from a length of steel with a rectangular…

A: Given Data

Q: A draw bar between a tractor and a trailer is made from a length of steel with a rectangular…

A: (i) Stess at secion X-Xσ=P(b-ϕn)A=1000 X 103(100-25) X 12σX-X=111.1MPawhere b and T→ width and the…

Q: For the shown static system, determine the minimum diameter of cable BD to withstand the shown load,…

A:

Q: A vertical force P is applied at a point C located on the axis of sym-metry of the cross section of…

A: The centroid of the column , y=y1A1+y2A2A1+A2 iny=5X6X2+2X4X26X2+4X2 iny=3.8 in

Q: The bell crank shown is in equilibrium for the forces acting in rods (1) and (2). The bell crank is…

A:

Q: Why is the net area for AB (0.045-0.0102) * (0.012) ? Why is AB in tension and BC in compression

A:

Q: In the structure shown, a 6-mm-diameter pin is used at C, and 10-mm-diameter pins are used at B and…

A:

Q: For the connection shown, the average shear stress in the 6-mm-diameter bolts must be limited to 176…

A:

Q: The 1.4-kip load P is supported by two wooden members of uniform cross section that are joined by…

A: Given Data: The load on member is P = 1.4 kip. The cross-section area is A = 3 in ×5 in. The angle…

Q: An eccentric load is applied at a point 22 mm from the geometric axis of a 60-mm-diameter rod made…

A: The diameter is .The eccentric distance is .The yield stress is .The young modulus is .The length is…

Q: Given the assembly shown is a cylinder rod position vertically and is supported by a collar and a…

A: Shear failure between collar and cylinder: Area of shear occurs between collar and cylinder…

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.